Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
19f. EMPTYING SYSTEM BEFORE TRANSPORT This procedure is necessary to prevent water and frost damage in case you intend to transport your Impressa F9. • Turn machine off. • Place a cup underneath the frother. • Push and hold the Steam Button until the display shows: SYSTEM EMPTYING. The machine will push a bit of water and steam into the cup underneath the frother. After about 30 seconds it will turn off automatically. Important: The next time you turn the machine on you must follow the instructions in chapter 6. Please note: Before transporting the machine, make sure that the water tank is empty, the filter cartridge is removed (discard and use a new cartridge), the bean container is empty, the drawer 22. and used coffee container are empty and clean. Secure the lids of the water tank and the bean container with scotch tape. Pack entire machine with thick cushioning material on all sides to prevent damage. 20. AUTOMATIC CLEANING CYCLES 20a. CLEANING WITH SPECIAL TABLET The machine monitors how many coffees are brewed and how often the rinsing program is activated. After approx. 200 coffees the display will show CLEAN MACHINE SELECT PRODUCT. Please note: You can continue to make coffee, however we highly recommend that you clean the machine as described below within the next few days. This cleaning program will remove oil build-ups in the brewing chamber. This cleaning program takes about 15 minutes. Please use one white cleaning tablet (enclosed). The machine comes with a pack of 2 tablets. To re-order cleaning tablets see chapter 22. Important: Once the cleaning program has started do not interrupt the procedure. • Make sure the machine is on and the water tank is full. • Push and hold the Rinse button until the display shows EMPTY TRAY. • Remove and empty the drawer and replace complete assembly (Fig. 23). Important: Even if the drawer is empty, you still need to remove it for approx. 20 seconds and then replace it. The display shows PRESS MAINT. • Push the Rinse Button (Fig. 3b). The display shows MACHINE CLEANING. After a moment the machine beeps and the display shows TABLET PRESS MAINT.. • Open the ground coffee lid and drop in one white cleaning tablet (Fig. 24). • Push the Rinse button. The display shows MACHINE CLEANING. The cleaning program will dispense hot water in intervals through the coffee spout into the drawer. • When finished, the display shows EMPTY TRAY and the machine "beeps". • Lift and remove the drawer. Empty the used coffee container and drawer and replace. The display shows SELECT PRODUCT indicating the machine is now ready to brew coffee again. 20b. DECALCIFYING PROCEDURE The machine has an integrated decalcifying program. When the display shows MACHINE SCALED SELECT PRODUCT it is time to decalcify the machine. You can still make coffee however, it is highly recommended that you decalcify the machine within the next 3 to 4 days. Please note: If you use the Claris water cartridge and the display shows MACHINE SCALED SELECT PRODUCT, then your cartridge function is not activated. Follow the instructions in chapter 16a to program the Claris Cartridge function. Important: The decalcifying program must not be interrupted. DECALCIFYING AGENT: Only use our special decalcifying tablets. For supplies see chapter 22. CAUTION: Never use vinegar or any other decalcifying agent. This might damage internal parts of the machine. 1. Turn off machine and let cool down for at least one hour. Empty Water tank. 2. With the machine off, push and hold the Rinse Button (Fig. 3b) until the display shows EMPTY TRAY. 3. Remove and empty the drawer and replace complete assembly (Fig. 23). Important: Even if the drawer is empty, you still need to remove it for approx. 20 seconds and then replace it. The display shows AGENT IN TANK PRESS MAINT.. 4. Dissolve three of the large, square tablets in 16 oz. of water and pour this mixture into the water tank. Please note: Do not use more than 16 oz. of water. 5. Replace water tank. 6. Place a container (at least 16 oz.) underneath the frother. The displays still shows AGENT IN TANK PRESS MAINT. 7. Push the Rinse Button. The machine will pump the mixture through the frother in intervals. Then it pumps the mixture (internally) into the drawer. During this procedure the display shows MACHINE DESCALED. When this cycle is finished the machine beeps and the display shows EMPTY TRAY. 8. Remove the container from underneath the frother. Carefully lift and remove the drawer, empty and thoroughly rinse all parts and replace. The display shows FILL WATER. 9. Remove the water tank, rinse thoroughly, fill with cold fresh water (approx. 16 oz.) and replace. 10. Place a container (at least 16 oz.) underneath the frother. The display shows PRESS MAINT. FILL WATER. 11. Push the Rinse Button. First the machine will pump hot water in intervals through the frother to remove any decalcifying mixture. During this procedure the display shows MACHINE DESCALED. When the cleaning cycle is fini...