Évaluations - 0, GPA: 0 ( )

Fabricant : Philips Taille : 1.12 mb Nom Fichier : Langue d'enseignement:

B Longer extension cords are available and may be used if care is exercised in their use. C If a long extension cord is used: 1 the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance. 2 if the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord, and the longer cord should be arranged so that it will not drape over the counter top portable top where it can be pulled on by children or tripped over; ENGLISH 3 If the power supply cord has a polarized plug (one blade is wider than the other), as a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fi t, contact a qualifi ed electrician. Do not attempt to defeat the safety feature. 4 If damaged, the power cord must be replaced by the manufacturer or an authorised service centre. Preparation: 1. Remove the water tank cover (22) and fill the tank with cold water checking the level through the tank window shown in FIG. 02. N.B.: The upper section of the tank (6) is provided with an overflowing safety hole (16) in case of tank overfilling. The water tank can also be removed (FIG.02), after removing the tank cover (22). Re-install tank with water and cover (22). 2. Insert plug (19) into a suitable wall outlet (see point 1 under “Caution”). 3. Press the main switch (1), the start light (3) will light up. The temperature light (5) will light up fixed when the required temperature is reached; Circuit Priming N.B.: Upon first use, after dispensing steam or when the water tank is empty, the machine’s water circuit must always be primed. This machine, featuring a pump to brew coffee, is equipped with a self-priming system. Place an empty cup under the brewing head (14), do not insert the filter holder and press the hot water/coffee switch (2) (“1 Pos.). You will hear the sound of the operating pump, and after a few seconds, water will start flowing out of the brewing head (14). Warning! Before removing the water tank, make sure that the machine is off as not to damage the self-primer. When the cup is full,press again the hot water/coffee switch • 11 • ENGLISH ENGLISH (2) to stop dispensing. N.B.: The pump self-primer could be temporarily out of order because of an “air bubble”. In this case water does not flow from brewing head (14), and the following procedure should be followed: a) Place a small frothing pitcher or mug under the steam nozzle (8). b) Turn the knob (7) counterclockwise to open the steam/ hot water dispensing tap and press the hot water/coffee switch (2) to start dispensing. c) Alter a few seconds, a steady stream of water will emerge from the steam nozzle. Allow about one cup of water to fi ll the pitcher. Press the hot water/coffee switch (2) and close the steam/hot water tap (7) to stop dispensing. d) NOTE: The temperature ready-light (5) will automatically flash as the machine boiler heats. After switching on the machine for the first coffee, wait 6 minutes until the machine has fully heated up, while for all subsequent coffees the machine will be ready to use. Caution: Never operate pump without water in machine as damage to the pump may occur. Damage of pump run without water is not covered by warranty. Using the machine for the first time or after a period of inactivity This simple operation ensures an optimum brewing and must be performed: - at first start-up; - when the machine remains inactive for a long time (more than 2 weeks). NOTE: Dispensed water must be emptied into an adequate drain. It is not suitable for food use. If the container fills up, stop dispensing water during the cycle and empty it before resuming the operation. A (Fig.02) - Rinse the tank and fill it again with fresh drinking water. B (Fig.03) - Place a container under the steam wand (Pannarello). Open the knob (7) slowly by turning it counter-clockwise and press the hot water/brew button (2). C Dispense half the water tank from the steam/hot water wand. To stop dispensing, press the hot water/brew button (2) again. Then close the knob (7) by turning it clockwise. D Insert the filter holder into the brew unit from the bottom (14) and turn it from left to right until it locks into place. E Place a suitable container under the filter holder. F Press the brew button (2) and dispense all the water left in the water tank. Once the tank is empty, stop dispensing by pressing the brew button again (2). At the end, empty the container. G Fill the tank again and wait until the “correct temperature” indicator light (5) turns on. H Remove the filter holder from the unit by turning it from right to left and rinse it with fresh drinking water. I The machine is now ready to be used. For further information on how to dispense hot water, please refer to sections "How to brew a good Espresso Coffee" and "Making Hot Water". • 12 • Important to know…… ENGLISH Warning! Never brew coffee when...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :