Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Two cup attachment for espresso coffee 15. Measuring spoon 16. Filter holder for espresso coffee 17. Filter for espresso coffee 18. Filter holder for drip coffee 19. Drip coffee pot 20. “ACCUFLAVOR” drip coffee aroma selector switch 21. “Vario system” espresso coffee aroma selector switch 22. Removable water tank 23. Lid for water tank 24. Boiler 25. Boiler cap 26. Steam release knob INSTALLATION • Place the appliance on a flat work surface away from water sources such as taps or sinks. • Check that the voltage of the electrical power line corresponds to the voltage indicated on the appliance label. Connect the appliance only to a power source having a minimum load capacity of 10 amps and having a proper grounding feature. The manufacturer takes no responsibility for any accidents caused by the lack of a grounding device for the appliance. • Never install the machine in an environment which can reach a temperature of less than or equal to 0°C (if the water inside the machine freezes, the machine might be damaged): HOW TO PREPARE DRIP COFFEE • Raise the lid and remove the water tank (fig. 1). • Fill the tank with cold, clean water, up to the level indicated on the tank corresponding to the number of cups of coffee that are desired (fig. 2). • Insert the tank into the machine by pressing it slightly. If desired, the tank can be left in its place and to fill it, the drip coffee pot can be used which also has the level indicators on it (fig. 3). • Open the filter holder by swinging it out to the left (fig. 4). • Place the paper filter into the filter holder (fig. 5). We recommend using #4 type paper filters. • Put the ground coffee into the filter by using the measuring spoon included with the machine and level off the grounds uniformly (fig. 6). As a general rule, use one level measuring spoonful of coffee (about 7 grams) for each cup of coffee (for example, use 10 measures to make 10 cups of coffee). In any case, the quantity of ground coffee to use can vary according to the strength desired and personal taste. Use high quality ground coffee, with a medium grind and the kind packaged especially for drip coffee makers. • Close the filter holder and place the pot, with its lid inserted, onto the hot plate. • Select the aroma desired as indicated in the paragraph “How to select the aroma”. • Press the “ON/OFF” switch for drip coffee (fig. 7). The ON indicator light for drip coffee above the switch itself indicates that the coffee machine filter is functioning properly. • If more than five cups of coffee are desired, press the switch (with the symbol) (fig. 8) and the indicator light will light up. If, on the other hand, five or fewer cups of coffee are desired, the switch should not be pressed. In this way, the hot water will flow more slowly through the ground coffee and a more flavourful beverage will be obtained. • The brewed coffee will begin to drip out after a few seconds. It is completely normal that during the percolation of the coffee, some steam may escape from the machine. • If you keep “ON/OFF” switch for drip coffee on the ON position after the percolation, the warming plate will maintain the hot coffee at an ideal drinking temperature. HOW TO SELECT THE AROMA OF THE DRIP COFFEE With the ACCUFLAVOR , it is possible to select the aroma of the dripcoffee depending on personal taste. By turning the aroma regulation knob of the coffee filter (fig. 9), the coffee machine can be programmed for a strong flavour (STRONG position) or a lighter flavour (LIGHT position). The ACCUFLAVOR feature changes the flavour of the coffee, more or less strong, while the taste of the coffee remains unchanged. HOW TO PREPARE ESPRESSO COFFEE 1. Unscrew the boiler cap by turning it in a counter-clockwise direction. 2. Using the level indications stamped on the WATER LEVEL side, fill the small pot with the amount of water suggested (fig. 10) according to the number of cups of espresso coffee that are desired (see the chart at the end of this text). 3. Pour the water into the boiler (fig. 11). 4. Replace the plug in the boiler cap by turning firmly in a clockwise direction. 5. Insert the filter for espresso coffee into the filter holder (fig. 12). 6. Fill the filter with the ground coffee, respecting the dosages indicated in the chart at the end of this text and distribute it uniformly in the filter (fig. 13). It is important to use the highest quality coffee and having a medium grind in order to avoid the obstruction of the filter during the brewing. Remove any excess coffee from around the edges of the filter (fig. 14). 7. To attach the filter holder to the appliance, position it under the boiler outlet with the handle towards the left, see fig. 15. Push upwards, and at the same time, turn the handle towards the right. Always turn right to the end. 8. Place the coffee pot for espresso coffee under the filter holder so that the spout where the coffee exits is inside of the opening on the lid of the coffee pot (fig. 16). 9. Pos...