Évaluations - 4, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Water refill indicator 2. ON-OFF/stand-by indicator 3. Start indicator 4. Hot water selector indicator 5. Steam selector indicator 6. Light selector indicator 7. Espresso coffee indicator 8. Regular coffee indicator 9. Used Coffee 'drawer full' indicator 10. ON-OFF/stand-by control 11. Start control 12. Hot water selector control 13. Steam selector control 14. Light selector control 15. Espresso coffee control 16. Regular coffee control TOUCH CONTROLS: Instructions for use These touch controls must be pressed precisely to prevent functions from being enabled accidentally. Pressing lightly on the respective symbol will enable the corresponding function. 4 INSTRUCTIONS FOR THE FIRST USE OF THE MACHINE FILLING UP THE WATER RESERVOIR • Squeeze together the unlocking levers found under the drip tray • Gently pull the coffee machine forward from the housing by sliding it along the telescopic runners. Hardness of water: • Before filling up the water reservoir, make sure that the decalcifying Brita filter has been soaked in cold water for at least 30 min. Follow the instructions printed on the filter package. After this operation insert the filter into position inside the water reservoir as shown in the figure. • If the machine will not be used for long periods, empty the water from tank. • Brita filters are available from most supermarkets and domestic goods outlets, at our After-Sales Service Centres or at the Shops of Authorized Spare Parts. • Remove the reservoir and fill it with approximately 2.5 litres of water as shown. • replace the water reservoir in its own housing taking care to fully engage the water valve into the docking station. • Ensure the mains ON/OFF switch(at rear) is ON • push the machine back into the housing until a “CLICK” can be heard. This indicate that the machine has been locked in position. FILLING UP THE CONTAINER WITH COFFEE BEANS • Press the unlocking levers located under the drip tray and pull the machine as it is shown in the figure. • pull the coffee machine forward from the housing along the telescopic runners . • Pour approximately 200g of coffee beans into the container on the top as shown in the figure. • Push the machine back into the housing until a “CLICK” can be heard. This indicate that the machine has been locked in position. INITIAL START-UP • Put the main switch in position 1 • The led corresponding to the ON-OFF control will blink rapidly for 3 minutes. • • The machine is be in stand-by mode when the ON-OFF LED is blinking slowly, it is then ready to be switched on. • Ensuring the water reservoir and the coffee beans container are full, switch the coffee machine on by pressing the on-off control and the corresponding LED stops flashing and remains lit. ADJUSTING THE TEXTURE GROUND COFFEE CAUTION • This machine is calibrated in the factory for an optimum level of ground coffee. Too “coarse” ground coffee will result in a weaker coffee. Too “fine” ground coffee will result in very strong coffee, delivered by “drops” and tasting “bitter”. The time required for an espresso will range from 20-30 seconds. • Press the unlocking levers located under the drip tray and pull the machine as shown in the figure. • Pull the coffee machine forward from it’s housing by sliding it along it’s telescopic runners. • Turning the knob will adjust the coffee texture. Before adjusting, make a note of the original setting so that the machine can be reset, if required, to the factory settings. Turning the knob in the clockwise direction will lead to a fine texture for a stronger coffee. Turning the knob anti-clockwise will lead to a coarse texture for a weaker coffee. The set grinding level can be read on the lid of the coffee case: bigger circles means “coarse” grinding level (fast-flowing weak coffee), whereas smaller circles means “fine” grinding level (slowflowing strong coffee). • Push the machine back into the housing until a “click” can be heard. This indicates that the machine is locked in position. STAND-BY MODE • Once powered and inserted into the cabinet, the machine is in stand-by mode: this will be signaled by the on/off LED blinking. • Press the start control to switch on the machine: the start LED will be illuminated. • To come back to the stand-by mode, press the start control once again. CAUTION: On start-up, the machine initiates the pre-warming phase for the first 3 minutes. During this phase the ON/OFF LED will blink quickly and the machine will be not able to execute any operation. Then the LED blinks slowly and the machine is ready to operate. 5 MAKING COFFEE • Press the control corresponding to the desired selection. • Press the start control within 10 seconds and the machine will make the coffee selected. • The machine will stop automatically CAUTION: the desired function will be disabled if the start control is not pressed within 10 seconds. It will then be necessary to repeat the procedure. HOW TO OBTAIN AN EXCELLENT ESPRESSO • The brewing time for an excellent espres...