Log:
Évaluations - 0, GPA: 4 ( )

Instructions Havis-Shields, Modèle DS-DELL-101-3

Fabricant : Havis-Shields
Taille : 5.63 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Zip Ties (4) 2. Keys (2) 3. 1/4”-20 Screws (4) 4. M5 Screws (4) Tools required for installation: • 3mm Hex Drive (For attaching Mounting Bracket to Docking Station with M5 Screws) • 5/32” Hex Drive (For attaching Mounting Bracket to Motion Device with 1/4”-20 Screws) Port Replication Capability Side Connectivity Rearward Connectivity *(Antennas for DS-DELL-101-3 only) Mouse Keyboard Antennas* (Wi-Fi, GPS, Cellular) Microphone Parallel (DB-25) VGA Display (x2) (HDMI Dongle Required) eSATA Headphone Ethernet USB 2.0 (x2) Power Input Serial USB 2.0 (x3) 5 • 1-800-524-9900 Installation 1) Install the Mounting Bracket to the Motion Device using (4) 1/4“-20 screws (Hardware Kit Item 3). Torque screws to 120 in-lbs (13.4Nm) ± 10%. NOTE: Numerous hole patterns present in Mounting Bracket will accommodate Havis Motion Devices as well as most competitors’. 1/4”-20 Screws Mounting Bracket Typical Motion Device Example (not included) 2) Lower the Docking Station to the Mounting Bracket as shown and secure with (4) M5 screws (Hardware Kit Item 4). Torque screws to 25 in-lbs (2.8 Nm) ± 10%. M5 Screws NOTE: We recommend applying a drop of medium strength (blue) thread locking adhesive to the threads of all fasteners. 6 Cable Management 1) Tip the Docking Station forward to a position that is comfortable to work with. 2) Install all cables that are necessary for computing needs. 3) Use Zip Ties (Hardware Kit Item 1) to strain relieve cables to the Strain Relief Points at rear of Docking Station. 4) Gather all cables to one side and tie off to unused holes on underside of Docking Station. Insert as many zip ties as necessary to secure cables. 7 • 1-800-524-9900 Cable Management (continued) 5) Create a service loop with cables to ensure that no tension is on the connectors and to enable intended motion. 6) Tie off cables onto a stationary part of the mounting system. (Mounting system not included with Docking Station) This loop must be large enough to allow full range of expected rotation and extension without stressing connections. Collect cables to secure to the mounting system (Note: mounting system not included) 8 Operation - Docking • DO NOT MATE COMPUTER TO DOCKING STATION UNLESS COMPUTER’S DOCKING CONNECTOR ACCESS DOOR IS FULLY OPEN OR DAMAGE MAY RESULT. • DO NOT FORCE LAPTOP ONTO DOCKING STATION. IF THERE IS RESISTANCE, CHECK ALIGNMENT OF COMPUTER ON DOCKING STATION. 1) To load the computer, first ensure Docking Station is unlatched by pushing the Lock to release the Latch Handle. Once Docking Station unlatches, release pressure on Lock to allow the Latch Handle to extend fully. Note: Red warning label on Latch Handle is visible when fully extended. 2) With rear of computer elevated, load front of computer into Docking Station by aligning Front Hooks with the appropriate recesses in the computer case. 3) Lower rear of computer onto Docking Connector. Blue Port Replication LED will illuminate once computer is properly seated. 4) ...

Ce manuel est également adapté pour les modèles :
Accessoires d'ordinateur - DS-DELL-101 (5.63 mb)
Accessoires d'ordinateur - DS-DELL-103 (5.63 mb)
Accessoires d'ordinateur - DS-DELL-221 (5.63 mb)
Accessoires d'ordinateur - DS-DELL-223 (5.63 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories