Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Attach the Dialogue LVD cable to the connector on the back of the Dialogue VCO. Be careful not to bend any pins. Figure 36 - Audio Output Socket Figure 37 - Connecting the Speech Processor DIALOGUE VCO M1 a. a. a. a. a. POWER RELAY REL MGS SPACEAUTO ANS SIGNAL M2 M3 M4 M5 SELECT MEMORY b X HOLD PROG LO HI FLASH REDIAL TONE VOL AMPLIFY Q Z ! $ () = " / ' + , . ? : ; b. b. b. b. b. 18 Figure 38 - Connecting the Dialogue LVD IN TTY/TDD MANUAL AUTO Connecting to the Q-90 Printer The Dialogue VCO can be used with the Q-90 Printer from Ameriphone. Attach the Q-90 Printer cable to the connector on the back of the Dialogue VCO. Connecting to the Dialogue LVD and the Q-90 Printer The Dialogue VCO can be connected to both the Dialogue LVD and the Q- 90 Printer through the use of an optional cable. The cable is available from Ameriphone and can connect the Dialogue LVD to the Q-90 Printer. The Ameriphone item number for the cable is #79028. Special Features (Continued) 19 Figure 39 - Connecting the Q-90 Printer MANUAL AUTO PAPER FEED PRINT SIZE ON/OFF LINE Figure 40 - Connecting the Dialogue VCO to the Dialogue LVD and the Q-90 Printer PRINTER TTY/TDD 12VDC 500mA MANUAL AUTO PAPER FEED PRINT SIZE ON/OFF LINE Troubleshooting Chart The chart below will help you solve most problems that may arise during operation of your telephone. Should the difficulty continue, contact Ameriphone or your authorized dealer for assistance. SYMPTOM CAUSE AND CORRECTIVE ACTION Screen remains blank No power. The screen runs on AC power, check that the AC adapter is plugged into the wall, and the receptacle is plugged into the Dialogue VCO. No dial tone 1. Check all phone cord connections. 2. Remove back-up battery if installed. Plug in AC adapter first then re-install battery. Letters do not appear when pressing keypad Still in telephone mode. Press SELECT to enter text mode. No number dialed when memory button pressed No number stored in that memory button. See “Programming Frequently Dialed Numbers.” Nothing happens when RELAY is pressed No number stored in the RELAY button. See “Programming the Relay Service Number.” Garbled message on screen Press SELECT once to correct the inco ing message. Call cannot be dialed, or is dialed slowly See "Installation" section to reset the dialing mode switch. Dialogue VCO does not have an audible ring Make sure the ringer is not set to "Off" position. 20 FCC Statement The DIALOGUE VCO has been registered with the Federal Communications Commission (FCC) and complies with the standards in Part 68 of the FCC Rules. FCC compliant telephone cords and modular plugs are provided with this telephone. Your telephone company is required by the FCC to allow you to connect FCC registered telephone equipment to their telephone lines. The FCC requires that upon the request of your local telephone company, you provide the FCC registration number and Ringer Equivalence Number (REN) of your telephone equipment, both noted on the underside of the Dialogue VCO. Your Dialogue VCO has been tested and found to meet the standards for a Class B digital device, as specified in Part 15 of the FCC Rules. These specifications are designed to provide against interference with radio and television reception in a residential installation. There is no guarantee that interference will not occur in a particular installation. If your Ameriphone product causes interference with radio or television reception when in use, you might correct that interference with any one or all of these measures: 1. Where it can be done safely, reorient the receiving television or radio antenna. 2. To the extent possible, relocate the television, radio or other receiver with respect to the telephone equipment. 3. If your telephone product runs on AC power, plug it into an AC outlet that is not on the same circuit as the one used by your radio or television. 21 Warranty This warranty applies only to Ameriphone products that are purchased and used in the United States or Canada. Ameriphone warrants the DIALOGUE VCO telephone against any defect in materials or workmanship for the period of one year from the date of purchase. If your Ameriphone product is defective and returned within 30 days of the date of purchase, your DIALOGUE VCO dealer will replace it at no charge. If returned after 30 days, but within one year from the date of purchase, we will repair or replace it at no charge. In the repair of your DIALOGUE VCO, we may use new or reconditioned replacement parts. If we elect to replace your DIALOGUE VCO, we may replace it with a new or reconditioned product of the same or similar design. Repair or replacement will be warranted for either 90 days or the remaining time on the original warranty period, whichever is longer. Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the product is fit for ordinary use), are limited to one year from date of purchase. We will not pay for loss of time...