Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
SiL3132 E-Sata Device (available on Aurora and Aurora ALX only) Allows you to enable and disable the e-SATA controller. JMicron-362 E-SATA Device (available on Aurora-R2 only) Allows you to enable and disable the e-SATA controller. Integrated Devices Configure SATA#1-6 as (available on Aurora and Aurora ALX only) Allows you to configure the integrated hard drive controller to AHCI or RAID. SATA Mode (available on Aurora-R2 only) Allows you to configure the integrated hard drive controller to AHCI or RAID. AHCI CD/DVD Boot Time out Allows you to set the wait time for SATA or CD/DVD in AHCI mode. Power Management Setup Suspend Mode Sets the energy-saving mode of the ACPI function. AC Recovery Sets what action the computer takes when power is restored. Remote Wakeup (available on Aurora and Aurora ALX only) Sets the system to wake up from an onboard LAN, PCIE-X1 LAN card, or a PCI LAN card. Auto Power On Allows the computer to start up at a certain time. Frequency/Voltage Control CPU Speed Displays the current processor speed. Memory Speed Displays the current memory speed. Current QPI Speed (available on Aurora and Aurora ALX only) Displays current QPI speed. Current DMI Speed (available on Aurora-R2 only) Displays current DMI speed. QPI Frequency (available on Aurora and Aurora ALX only) Allows you to change the QPI frequency. DMI Frequency (available on Aurora-R2 only) Allows you to change the DMI frequency. Memory Ratio Allows you to change the memory ratio. Core (Non-Turbo) Ratio Displays the ratio between the processor core clock and the FSB frequency. Advance DRAM Configuration Allows you to access the advance DRAM configuration submenu Overclock Configuration Allows you to access the overclock configuration submenu Frequency/Voltage Control Overvoltage Configuration Allows you to access the overvoltage configuration submenu Load Level1 OC Setting Allows you to restore the Level 1 overclocking settings that were shipped from the factory (only displayed with an XE processor). Advance DRAM Configuration Submenu Memory-Z Opens submenu to display the SPD configuration for each memory module. Advanced Memory Settings Allows you to toggle to Manual mode and set all of the timing parameters. tCL Displays the Column Address Strobe Latency (editable in Manual Mode). tRCD Displays timing of RAS to CAS delay (editable in Manual Mode). tRP Displays timing of RAS Precharge (editable in Manual Mode). tRAS Displays timing of Row Address Strobe (editable in Manual Mode). Advance DRAM Configuration Submenu tRFC Displays timing of Refresh to Archive/ Refresh cycle time (editable in Manual Mode). tWR Displays timing of Write Recover (editable in Manual Mode). tWTR Displays Write to Read delay (editable in Manual Mode). tRRD Displays RAS to RAS Delay (editable in Manual Mode). tRTP Displays Read to Precharge command delay (editable in Manual Mode). 1T/2T Timing Displays the Command Rate (editable in Manual Mode). Overclock Configuration Submenu Adjust CPU BClk (MHz) Allows you to adjust BClk of processor. Spread Spectrum Enable/disable spread spectrum modulation. Adjust PCI Frequency (MHz) (available on Aurora and Aurora ALX only) Allows you to adjust PCI frequency. Adjust PCI-E Frequency (MHz) Allows you to adjust PCI-E frequency. Intel® TurboMode tech If enabled, allows processor to run at faster frequencies than marked. [1-4] Core CPU Turbo Ratio Limit (available on Aurora and Aurora ALX only) Limit ratio for cores 1-4 (XE processors only). Turbo Mode TDC Limit Override Allows you to program the current thresholds for the processor while in turbo mode. Turbo Mode TDP Limit Override Allows you to program the power thresholds for the processor while in turbo mode. Overvoltage Configuration Submenu CPU Temperature Sensor Displays the processor temperature in Celsius and Fahrenheit. VCore Displays processor core voltage. Dynamic CPU VCore Offset Processor core voltage offset. DDR3 Memory Voltage Adjust the DDR3 memory voltage. IOH Voltage Adjust the IOH voltage. QPI and Uncore Voltage (available on Aurora and Aurora ALX only) Adjust QPI and uncore voltage. DMI and Uncore Voltage (available on Aurora-R2 only) Adjust DMI and uncore voltage. BIOS Security Features Change Supervisor Password Allows you to change the supervisor password. Change User Password Allows you to change the user password. You cannot use the user password to enter the BIOS setup, during POST. Exit Exit Options Provides options to Save Changes and Exit, Discard Changes and Exit, Load Optimal Defaults, and Discard Changes. Clearing Forgotten Passwords and CMOS Settings Follow the instructions in “Before You Begin” on page 1. 6. WARNING: The computer must be disconnected from the electrical outlet to clear the CMOS setting. Remove the left side-panel (see “Removing the Left Side-Panel” on page 2. 11). Reset the current password and CMOS settings: 3. Locate the 3-pin CMOS or password-reset jumper on the system board a. (see “System Board Components” on page ...