See "System Memory." Time-of-day Faulty battery or faulty chip. See "Troubleshooting the clock stopped System Battery." Time-of-day not Incorrect Time or Date Check the Time and Date set - please run settings; faulty system settings. See "Using the SETUP program battery. System Setup Program and UEFI Boot Manager." If the problem persists, replace the system battery. See "System Battery." About Your System Table 1-2. System Messages (continued) Message Causes Corrective Actions Timer chip Faulty system board. See "Getting Help." counter 2 failed TPM A TPM configuration Information only. configuration command has been entered. operation The system will reboot and honored. System execute the command. will now reset. TPM configuration operation is pending. Press (I) to Ignore OR (M) to Modify to allow this change and reset the system. WARNING: Modifying could prevent security. This message displays during Enter I or M to proceed. system restart after a TPM configuration command has been entered. User interaction is required to proceed. TPM failure A Trusted Platform Module See "Getting Help." (TPM) function has failed. Unable to launch System Services image. System halted! System halted after keystroke because System Services image is either corrupted in the system firmware, or the system firmware has been lost due to system board replacement. Restart the system and update the Unified Server Configurator respository to the latest software to restore full functionality. See the Unified Server Configuration user documentation or more information. About Your System Table 1-2. System Messages (continued) Message Causes The iDRAC6 Enterprise card flash memory may be corrupted. Corrective Actions Restore the flash memory using the latest version on support.dell.com. See the iDRAC6 user’s guide for instructions on performing a field replacement of the flash memory. Unexpected Improperly seated memory Reseat the memory modules. interrupt in modules or faulty See "Troubleshooting System protected mode keyboard/mouse controller Memory." If the problem chip. persists, see "Getting Help." Unsupported CPU Processor(s) is not supported Install a supported processor combination by the system. or processor combination. See "Processors." Unsupported CPU stepping detected Unsupported DIMM Invalid memory Ensure that the memory detected. The configuration. The system modules are installed in a following DIMM will run but with the valid configuration. See has been specified DIMM disabled. "System Memory." disabled: x Unsupported Invalid memory Ensure that the memory memory configuration. DIMMs are modules are installed in a configuration. mismatched in the specified valid configuration. See DIMM mismatch slots. "System Memory." across slots detected: x,x,... Unused memory detected. DIMMs installed in the following slot are not available when in mirror or 128-bit advanced ECC modes: x,x,x The memory configuration is not optimal for mirroring or Advanced ECC Memory Mode. Modules in the specified slots are unused. Reconfigure the memory for Memory Mirroring or Advanced ECC Memory Mode, or change the memory mode to Optimized in the BIOS setup screen. See "System Memory." About Your System Table 1-2. System Messages (continued) Message Causes Corrective Actions Warning: A fatal error has caused system reset! Please check the system event log! A fatal system error occurred and caused the system to reboot. Check the SEL for information that was logged during the error. See the applicable troubleshooting section in "Troubleshooting Your System" for any faulty components specified in the SEL. Warning! Control The control panel is not Install the control panel, or panel is not installed, or has a faulty cable check the cable connections installed connection. between the display module, the control panel board, and the system board. See "Installing the Control Panel Display Module." Warning! No micro Micro code update failed. Update the BIOS firmware. code update See "Getting Help." loaded for processor n Warning! Power required exceeds PSU wattage. Check PSU and system configuration. Warning! Performance degraded. CPU and memory set to minimum frequencies to meet PSU wattage. System will reboot. The system configuration of processor(s), memory modules, and expansion cards may not be supported by the power supplies. If any system components were just upgraded, return the system to the previous configuration. If the system boots without this warning, then the replaced component(s) are not supported with this power supply. If Energy Smart power supplies are installed, replace them with the High Output power supplies to use the components. See "Power Supplies." About Your System Table 1-2. System Messages (continued) Message Warning! PSU mismatch. PSU redundancy lost. Check PSU. Causes A High Output power supply and an Energy Smart power supply are installed in the system at the same time. Corrective Actions Install two High Output or two...
)
