Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Parallel port connector (26-1 pin LPT1) 4-14 12. BMC connector (16-pin BMCCONN1) 4-14 13. System panel auxiliary connector (20-pin AUX_PANEL1) LAN1 Link activity LED (2-pin LAN1_LINKACTLED) LAN2 Link activity LED (2-pin LAN2_LINKACTLED) Locator LED 1 (2-pin LOCATORLED1) Locator LED 2 (2-pin LOCATORLED2) Locator Button/Switch (2-pin LOCATORBTN) Front Panel System Bus (6-1 pin) 4-15 14. System panel connector (20-pin PANEL1) System power LED (Green 3-pin PLED) Hard disk drive activity LED (Red 2-pin IDE_LED) System warning speaker (Orange 4-pin SPEAKER) ATX power button/soft-off button (Yellow 2-pin PWRSW) Reset button (Blue 2-pin RESET) 4-16 ASUS AP1600R-E2 (BA2) ASUS AP1600R-E2 (BA2)ASUS AP1600R-E2 (BA2)ASUS AP1600R-E2 (BA2)ASUS AP1600R-E2 (BA2)ASUS AP1600R-E2 (BA2) 4.2 Jumpers 1. 1.1.1.1.1.Clear RTC RAM (CLRTC1) Clear RTC RAM (CLRTC1)Clear RTC RAM (CLRTC1)Clear RTC RAM (CLRTC1)Clear RTC RAM (CLRTC1)Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2. 4. Re-install the battery. 5. Plug the power cord and turn ON the computer. 6. Hold down the key during the boot process and enter BIOS setup to re-enter data. Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure! NCLV-D NCLV-D Clear RTC RAM CLRTC1 21 32 Normal Clear CMOS (Default) You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the C.P.R. (CPU Parameter Recall) feature. Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values. Chapter 4: Motherboard information Chapter 4: Motherboard informationChapter 4: Motherboard informationChapter 4: Motherboard informationChapter 4: Motherboard informationChapter 4: Motherboard information 2. 2.2.2.2.2. VGA Graphics controller setting (3-pin VGA_EN1) VGA Graphics controller setting (3-pin VGA_EN1)VGA Graphics controller setting (3-pin VGA_EN1)VGA Graphics controller setting (3-pin VGA_EN1)VGA Graphics controller setting (3-pin VGA_EN1)VGA Graphics controller setting (3-pin VGA_EN1) These jumpers allow you to enable or disable the onboard ATI Rage XL video graphics controller. Set to pins 1-2 to enable the video graphics controller. NCLV-D NCLV-D VGA Setting VGA_EN1 Enable (Default) Disable 2 3 2 1 3. 3.3.3.3.3.USB device wake-up (3-pin USBPW12, USBPW34) USB device wake-up (3-pin USBPW12, USBPW34)USB device wake-up (3-pin USBPW12, USBPW34)USB device wake-up (3-pin USBPW12, USBPW34)USB device wake-up (3-pin USBPW12, USBPW34)USB device wake-up (3-pin USBPW12, USBPW34) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). NCLV-D USBPW12 12 23 +5V +5VSB (Default) USBPW34 12 23 +5V +5VSB (Default) NCLV-D USB device wake-up • The USB device wake-up feature requires a power supply that can provide 500mA on the +5VSB lead for each USB port; otherwise, the system would not power up. • The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode. ASUS AP1600R-E2 (BA2) ASUS AP1600R-E2 (BA2)ASUS AP1600R-E2 (BA2)ASUS AP1600R-E2 (BA2)ASUS AP1600R-E2 (BA2)ASUS AP1600R-E2 (BA2) 4. 4.4.4.4.4.Keyboard power (3-pin KBPWR1) Keyboard power (3-pin KBPWR1)Keyboard power (3-pin KBPWR1)Keyboard power (3-pin KBPWR1)Keyboard power (3-pin KBPWR1)Keyboard power (3-pin KBPWR1) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS. KBPWR1 NCLV-D NCLV-D Keyboard power setting (Default) +5V 12 23 +5VSB 5. 5.5.5.5.5.Gigabit LAN controller setting (3-pin LAN_EN1) Gigabit LAN controller setting (3-pin LAN_EN1)Gigabit LAN controller setting (3-pin LAN_EN1)Gigabit LAN controller setting (3-pin LAN_EN1)Gigabit LAN controller setting (3-pin LAN_EN1)Gigabit LAN controller setting (3-pin LAN_EN1) These jumpers allow you to enable or disable the onboard Broadcom BCM5721 Gigabit LAN controller. Set to pins 1-2 to activate the Gigabit LAN feature. NCLV-D NCLV-D LAN_EN1 sett...