Évaluations - 4, GPA: 4 ( )

Fabricant : Carrier Taille : 3.85 mb Nom Fichier : Langue d'enseignement:

Your Room Air Conditioner was designed for easy installation in a vertical (slider type) windows. NOTE: This unit is NOT designed for single or double-hung windows. NOTE: Save the shipping carton and packing materials for future storage or transport of the unit. Please check the contents of hardware kit against the corresponding model check list, prior to installation of the unit. See lists below.(Fig.A) 3/8"Screws (4) End Cap & Leveling Leg (1) Nuts(2) Fig. A Installation Hardware Washers(2)1"Screws (2) Support platform(1) Support angles (1) Speed clips(2) Filler panel(1) Side channels(2) Sliders(2) Top channel(1) Seals (2) Factory installed Factory installed Shorter seal (1) Side seals (2) Factory installed Bottom bar(1) Factory installed 7/16" Screws(2) Top retainer (1) Foam (1) NOTE: Surplus screw(s) for spare use. Tools Needed for Window Installation Screw drivers: Both Philips and flat head Power drill: 1/8 inch diameter drill bit Pencil Measuring tape Scissors Carpenters level 6 AC 12 10 8 6 MAN final 3/2/05 12:55 PM Page 9 INSTALLATION INSTRUCTIONS A Leveling bolt Support angle Support platform 7/16"Screws B Two 1"long self-tapping screws Support platform assembly Lower window track Seal Shorter seal Topretainer Filler panel Sliders C Sliding Window Installation 1.Choose theinstallation site. It is imperative that the window frame assembly andthe side ofthe structure areadequate to support the weightof the unit.Reinforce if necessary. 2.Slide openone window sashto install support platform. 3.Loosely attachsupport angle tobottom of supportplatform using two 7/16 screws, washers andnuts. (See fig.A) " 4.Place support platform against lower window track and firmly against verticaledge of windowframe. 5.Attach support platform to windowsill using two1" self-tapping screws. Toovercome interference ofsupport the Platform with windowtrack or stormwindow, securely attach a 2" wide shim stripto the windowsill. The strip should beas long as thewidth of thesupport platform and flush withthe back edge of thesill.The thickness of the strip shouldbe controlled by the amountof interference.(See fig.B) 6.Pull supportangle against outsideof structure. Tighten two 7/16" screws on topof the supportplatform. 7.Adjust leveling boltto position supportangle in alevel plane. This will allow forthe proper angle.Tighten leveling bolt locknut. Important: Unit mustbe level ortilted back slightlyto facilitate proper condensatedisposal. Caution: Do notdrill a holein the bottompan. The unit is designed tooperate with approximately 1/2" of water in thebottom pan. 8.Cut two piecesof adhesive seal to height ofwindow opening. Remove backingand apply toverticalinside edges of window frame and slidingsash that willrest against unit.(See fig.C) 9.Slide unit ontosupport platform. Besure unit side channel butts againstvertical edge ofwindow frame. Note: If unitside channel doesnot fit securely, remove unit andreadjust leveling bolt. 10.Drill two 1/8 10.Drill two 1/810.Drill two 1/8 holes through window holes through windowholes through window channel frame channel framechannel frame " "" in alignment withexisting holes inbottom bar. Install two 3/8 long self-tapping screwsthrough these holes. " If the windowchannel frame isnot tall enough to use existing holes, drillnew holes off to theside of the existing holes toattach the unitbottom bar tothe support platform.The unitshould be firmly anchored to the window channel frame or support platform.(Seefig. D) 11.Slide inside window sashclosed. Be surevertical edge of inside windowsash is pressedfirmly against sideof u...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :