Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
2. Using the tab, pull up slightly on the filter to release it and pull it down or up. 3. Clean the filter with warm, soapy water below 40°C (104°F). 4. Rinse and gently shake the water from the filter and let it dry before replacing it. CAUTION: DO NOT operate the air conditioner without a filter because dirt and lint will clog it and reduce performance. Care and Maintenance TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET. • Do not use rechargeable batteries. Such batteries differ from standard dry cells in shape, dimensions, and performance. • Remove the batteries from the remote controller if the air conditioner is not going to be used for an extended length of time. • Keep the remote control away from infants and small children to prevent them from accidentally swallowing the batteries. How to insert batteries 1. Remove the cover from the back of the remote controller. 2. Insert two AAA dry cell batteries. • Be sure that the (+) and (-) directions are correct. • Be sure that both batteries are new. 3. Re-attach the cover. 9 Features and Installation Learning parts name prior to installation will help you understand the installation procedure. Features Features CABINET FRONT GRILLE AIR FILTER AIR INTAKE (INLET GRILLE) AIR DISCHARGE HORIZONTAL AIR DEFLECTOR (VERTICAL LOUVER) VERTICAL AIR DEFLECTOR (HORIZONTAL LOUVER) EVAPORATOR POWER CORD BASE PAN CONDENSER COMPRESSOR BRACE CONTROL BOARD REMOTE CONTROLLER Installation Features and Installation About 1/2" Over 20" Heat Radiation Fence Awning INSIDE OUTSIDE Foam Cooled Air 30-60" Level 1/4 Bubble How to Install the Unit 1. To prevent vibration and noise, make sure the unit is installed securely and firmly 2. Install the unit where the sunlight does not shine directly on the unit. 3. The outside of the cabinet must extend outward for at least 30.5 cm(12") and there should be no obstacles, such as a fence or wall, within 50.8 cm(20") from the back of the cabinet because it will prevent heat radiation of the condenser. Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner. CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure. 4. Install the unit a little slanted so the back is slightly lower than the front (about 12.7 mm(1/2")). This will force condensed water to flow to the outside. 5. Install the unit with the bottom about 76.2~152.4 cm(30"~60") above the floor level. Window Requirements NOTE: All supporting parts should be secured to firm wood, masonry, or metal. WINDOW REQUIREMENTS 1. This unit is designed for installation in standard double hung windows with actual opening widths from 29" to 41". The top and bottom window sashes must open sufficiently to allow a clear vertical opening of 18" from the bottom of the upper sash to the window stool. 2. The stool offset (height between the stool and sill) must be less than 1 1/4". 29" to 41" 18" min Offset Sill Exterior Interior Wall Stool 10 Installation Kits Contents Foam-PE (Adhesive-Backed) Foam-PE (Adhesive-Backed) Foam strip (Plain-Back) Right frame curtain Drain pipe Window locking bracket Left frame curtain Sill bracket(2) Support bracket(2) Top retainer bar is in product package. Type C (5) Type D (2)Type A (14) Carriage Bolt (2) Lock Nut (4) Type B (7) Features and Installation 11 12 Features and Installation Foam-PE Top retainer bar Top retainer bar Foam-PE Screw (Type A) Screw (Type A) Shipping screws Lower guide PREPARATION OF CHASSIS 1. Remove the screws which fasten the cabinet at both sides and at the back.(See Fig.1) 2. Slide the unit out from the cabinet by gripping the base pan handle and pulling forward while bracing the cabinet.(See Fig. 2) 3. Cut the window sash seal to the proper length. Peel off the backing and attach the Foam-PE to the underside of the window sash.(See Fig. 3) 4. Remove the backing from Foam-PE with 3 holes and attach it to the bottom of the Top retainer bar.(See Fig. 3) 5. Attach the Top retainer bar the top of the cabinet with 3 screws (Type A).(See Fig. 4) 6. Insert the Frame Curtain into the Top retainer bar and Lower guide.(See Fig. 4) 7. Fasten the curtains to the unit with 10 screws (Type A) at both sides.(See Fig. 4) Suggested Tool Requirements SCREWDRIVER(+, -), RULER, KNIFE, HAMMER, PENCIL, LEVEL Fig. 1 Fig. 2 Fig. 3 Fig. 4 Features and I nstallation Fig. 5 Fig. 6 Fig. 7 Fig. 8 SupportBracket Lock nut Sill Bracket CarriageBolt (Type M) Window sash Top retainer bar Cabinet Foam-PE Frame curtain Screw (Type B) Front Angle Sash track Foam-PE Cabinet Track hole SupportBracket Carriage boltand lock nut Machine screw (Type D) and lock nut Outer edgeof window sill Screw (Type B) Sill bracket Features and Installation Fig. 5 Fig. 6 Fig. 7 Fig. 8 SupportBracket Lock nut Sill Bracket CarriageBolt (Type M) Window sash Top retainer bar Cabinet Foam-PE Frame curtain Screw (Type B) Front Angle Sash track Foam-PE Cabinet Track hole SupportBracket Carriage boltand lock nut ...