Évaluations - 0, GPA: 0
(
)
)
|
Photos et spécifications LG M30L3H |
Facilité d'utilisation
Setting the Time 1 Time can be set only when you have pressed the Reset button. If you have just replaced the batteries, the Reset button should be pressed to reset the time. Press the Start/Stop button. Delay Start/Pre-Set Stop 2 3 1 Make sure the time is set correctly on the remote control display. OFF Press the ON/OFF Timer ON buttons to turn Timer on or off. Press the Time Setting buttons until the desired time is set. To cancel the Sleep Mode, press the sleep Mode Auto button several times until the star ( ) disappears from the operation display. Note: The Sleep Mode will be operated at low fan speed (cooling) or medium fan speed (heat pump only) for quiet sleeping. IN COOLING MODE: The temperature will automatically rise by 1°C over the next 30 minutes and by 2°C in 1 hour for comfortable sleeping. 2 Press the Time Setting buttons until the desiredtimeisset. 3 Press the Timer SET button. SET Note: Check the indicator for A.M. and P.M. 4 Press the selected on/off setting by SET pressing the Timer SET button while aiming the remote control at the signal receptor. To cancel the setting the timer. Press the Timer Cancel button while CANCEL aiming remote control at the signal receptor. (The timer lamp on the air conditioner and the display will go out.) ENGLISH NOTE: Select one of the following four types of operation. with the unit running Delay OFF Timer Delay ON Timer Delay OFFand ON Timer Delay ONand OFF Timer 13 Vertical Airflow Direction Control The up/down airflow (Vertical Airflow) can be adjusted by using the remote control. Press the Start/Stop button to start the unit. Open the door on the remote control. Press Chaos Swing button and the louvers will swing up and down. Press the Chaos Swing button again to set the vertical louver at the desired airflow direction. Note: . If you press the CHAOS swing button, the horizontal airflow direction is changed automatically based on the CHAOS algorithm to distribute the air in the room evenly and at the same time to make the human body feel most comfortable, as if enjoying a natural breeze. . Always use the remote control to adjust the up/down airflow direction. Manually moving the vertical airflow direction louver by hand could damage the air conditioner. . When the unit is shut off, the up/down airflow direction louver will close the air outlet vent of the system. To adjust left/right(Horizontal Airflow) direction Caution : Ensure unit is turned off before adjusting the horizontal airflow direction control. Carefully open vertical louver to allow access to the horizontal airflow direction. Adjust the left/right airflow direction by hand. Air Circulation Mode Circulates the room air without cooling or heating. 1 2 Press the Start/Stop button. the unit will respond with a beep. Open the door on the remote control. Press the Air Circulation button. Close the door on the remote control. Now each time that you press the Indoor Fan Speed Selector, the fan speed is shifted from low to CHAOS and back to low again. Fan speed is on low. Fan speed is on medium. Fan speed is on high.CHAOS Air Note: . CHAOS Air economizes power consumption and prevents overcooling. The fan speed is automatically changed from high to low or vice versa, depending on the ambient temperature. 14 Slide Switch Operation FORCED OPERATION Operation procedures when the remote control can't be used. Open the front panel upward and move the Slide Switch to the Forced Operation position. If you want to stop operation, move the Slide Switch to the Auto Restart or the Remote Control position. In case the power comes on again after power failure on the Forced Operation position, the operating conditions are automatically set as follows: During Forced Operation, the initial mode continues. Open the front panel upward Slide Switch Slide Switch FORCED OPERATION AUTO RESTART REMOTE CONTROL ENGLISH Cooling Model Heat pump Model Room Temp. . 24°C 21°C . Room Temp. < 24°C Room Temp. < 21°C Operating mode Cooling Cooling Healthy Dehumidification Heating Indoor FAN Speed High High High High Setting Temperature 22°C 22°C 23°C 24°C Auto restart In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate procedures automatically to the previous operating conditions. If you want to use this operation, Open the front panel upward and move the slide switch to the Auto Restart position. If you do not want to use this operation, move the Slide Switch to the Remote Control position. HELPFUL INFORMATION Fan speed and cooling capacity. The cooling capacity indicated in the specification is the value when the fan speed is set to high, and the capacity will be lower at low or medium fan speed. High fan speed is recommended when you wish to cool the room quickly. Slide Switch Open the front panel upward Slide Switch FORCED OPERATION AUTO RESTART REMOTE CONTROL When you are out for a while, put the Slide Switch on the Remote Control. HighSpeed 15 16 Care and maintenance of...