ProduCt SPeCifiCationS ProduCt SPeCifiCationS nomenClature CPH0900303B***A* 1234,5,67,8,910111213141516RevisionLevelsMajor&MinorBrandFactory-­.Installed Op7onsCCommercialXNo OpConsANon-­.powered convenience outletConfigura7onBPowered convenience outletPPackaged UnitCLow-­.ambient kitDReturn aismoke detectorApplica7onESupplyairsmoke detectorCCoolingFNon-­.powered convenience outlet; GGasHeatLow-­.ambient kitHHeat PumpGNon-­.powered convenience outlet; Return aismoke detectorNominal Gross Cooling

IO-357A 5151 San Felipe, Suite 500, Houston, TX 77056 3/10 © 2009 - 2010 Goodman Manufacturing Company, L.P. *NOTE: Please contact your distributor or our website for the applicable Specification Sheet or Technical Manual referred to in this manual. This Forced Air Central Unit Design Complies With Requirements Embodied in The American National Standard / National Standard of Canada Shown Below. ANSI Z21.47•CSA-2.3 Central Furnaces RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION. ATTENTION INSTALLI

Available as a factory-installed option on 3- to 12A-ton units. Hail guards are standard on 15- and 20-ton units. C • Stainless-Steel Heat Exchanger (CPG units only): A tubular heat exchanger made of 409-type stainless steel is installed in the unit. D • Ultra-Gold Condenser Coil: Offers increased corrosion resistance of the condenser coil. Not available for 15- & 20-ton units. • Low-Ambient Kit: Allows for cooling operation at lower outdoor temperatures. On the 3- to J 6-ton units, cooling

• All field piping must be installed by a licensed refrigeration technician and must comply with all national and local codes. • Never plug unit(s) into an electrical outlet. • Do not touch compressor, pipes and valves without protective gloves during and after operation, because these parts may become hot (more than 100°C (212°F). • Explain the operating procedure of the air conditioner to the customer. Outdoor unit mounting leg dimension additional refrigerant amount =0.22oz./ft.>25’. 18/24 Bt

MANUAL OPERATION • In case you are not satisfied with various conditions of automatic operation, you can select these conditions as you wish. • Select HEAT, DRY, Cool or CIRCULATE mode as you wish. OPERATION (Continued) OPERATION (Continued) HEAT MODE (Except Cool model) • In case of Cool and Dry mode, water may drop according to the contaminating status of air filter. In this case, please clean or replace the air filter with a new one. ! CAUTION ! • ..........Heating Capability: ~ This is a Hea

tion. Then press the ON/OFF button again, the unit will be set to the previous operating mode. • Upon input, one-hour timer is set at display and 0:30 is indicated current time. • If 1hr timer is set, the remaining minutes will be indicated. NOTE: • If pressing the 1HR TIMER button again during the ONE HOUR TIMER mode, the unit will stop operation approximately one (1) hour later. • The ONE HOUR TIMER mode has preference over other Timer modes. If pressing the 1HR TIMER button again during the O

ECR International Hyundai Ductless Split System6 mark will blink button. OPERATION (Continued) OPERATION CONDITION TIMER MODE (ON, OFF) mark will blink button. OPERATION (Continued) OPERATION CONDITION TIMER MODE (ON, OFF) • The timer can be set during any mode. Select the timer setting by pressing: ON-TIMER button or OFF-TIMER button. (Example) Time is AM 10:20. Air-conditioner is not in operation. How to start the air conditioner at PM 1:30 and stop it at PM 6:30. mark will blink 1. Press the

(Take care not to twist or crimp pipes during installation.) For Right Rear Sided, Right Sided and Lower Sided Piping NOTE: Do not apply excessive force to these parts. 1. For right side and lower side piping, cut the indoor unit base(s) with a hacksaw and deburr the cut end with a file. (See Fig. 5) 2. Hang the indoor unit(s) on the upper portion of the installation plate while inserting the vinyl-taped pipes through the wall hole. Engage the lower projection with the claws of the installation

• When the set temperature is to be changed: Room Temperature Over 27°C (81°F) 20~27°C (68~81°F) Below 20°C (68°F) OperatingMode Cool Dry Heat Set Temp. Monitor 24°C (75°F) 26°C (79°F):18/24K 27°C (81°F):9/12K............ • The room temperature is adjustable as you desire by pressing the room temperature setting. • The adjustable range is up to 4°C (8°F) plus or minus. • Automatic operation will not show the set room temperature. • The room temperature automatically appears in the display indica

B. Remove burrs from cut edges of pipes, which may cause a gas leak. C. Flaring of the pipe is done with the flaring tool. NOTE: Do not forget to install the flare nut before flaring 2. Pre-Connecting: Screw the tubing turning 3 to 5 times until hand tight. 3. Fastening: Fasten the connection. • Apply refrigeration oil to the flare surface to pre- vent gas leakage. Air Purge and Charging! CAUTION ! 1) Remove the cap from the service port on the suction line service valve. 2) Connect the suction