2009 - REV. 0 Printed in U.S.A. DistributedBy: Ordering Information “The Stinger has earned the trusted ARI Performance Certified™ seal, an assurance of the product’s performance in accordance with ARI Standard 740.” The new Stinger™ comes equipped with the new vacuum shut off allowing for unattended recovery operation, an easy-to-read low vacuum/tank full LED, carrying strap, and improved packaging to protect knobs and gauges. Providing you with new safety and reliability, the upgraded Stinger™

of the right side. There are two kinds of method to install the drain cap. The rear side of the unit The first method is that the shape of hole like It is good for the household. The second method is that the shape of hole is like It is good for the shop. • DOOR VENT The door vent for the room air ventilation is lever type. If the door vent lever moves to the left, then close the vent and moves to the rght, then open the vent. Close Vent Open Drain Cap SEAL DRAIN Screw (Type D) Door Vent > 11 CA

4. Consumer must pay charges for wiring and installation. 3 • SAFETY INSTRUCTIONS (CONTINUED) The receptacle should be an individual branch circuit used only for this air conditioner. Be sure the electrical service is adequate for the model air conditioner you have chosen. The complete electrical rating of your air conditioner is stated on the name plate located at the unit’s side. Be sure the plug receptacle is close enough for the power cord to reach it. WARNING : An extension cord should not

However, if you still elect to use an extension cord, it is absolutely necessary that it will be a UL listed 3-wire grounding type appliance extension cord rated has a 3-blade grounding plug and a 3-slot receptacle that will plug into the appliance. The marked rating of the extension cord should be 125V/13A minimum for DWC-100C, DWC-100CS, DWC-121C, DWC-121CS and 250V/10A minimum for DWA-122C, DWA-122CS, DWA-150C, DWA-150CS, DWA-151C, DWA-151CS. WARNING : To avoid death, personal injury or prope

However, if you still elect to use an extension cord, it is absolutely necessary that it will be a UL listed 3-wire grounding type appliance extension cord rated has a 3-blade grounding plug and a 3-slot receptacle that will plug into the appliance. The marked rating of the extension cord should be 125V/13A minimum for DWC-100C, DWC-100CS, DWC-121C, DWC-121CS and 250V/10A minimum for DWA-122C, DWA-122CS, DWA-150C, DWA-150CS, DWA-151C, DWA-151CS. WARNING : To avoid death, personal injury or prope

1. Operate the Selector Switch to run or stop the unit. -Do not use Main Power Switch or Auxiliary Power Switch to operate unit. 2. Do not stick anything into the air outlet or inlet. -It is dangerous and it can cause injury or damage. 3. Avoid exposing your body directly to a continuous cool air - flow for long periods. -It is not good for your health. 4. Do not pour water on the unit to clean it. -It is dangerous and it can cause injury or damage. Never use solvents or harsh chemicals when cle

Sash Bracket (1 piece) Window Seal A (1 piece) Screw Type B SILL Screw Type A SILL BRACKET 480mm SASH 240mm 610~914mm • Step 3 - Preparation of Chassis 1. Pull the Air-filter out of the Front Grille. 2. Loosen screw which fasten Front Grille with driver. 3. Pull knobs out of the control. (when the knobs are too tight to release, leave them.) 5 6 4. Disassemble Front Grille from Chassis. – Front Grille and chassis are fixed with snap-fit. 1) Release right-lower snap-fit. – Push the right lower si

A tight seal is essential. Read through the Use & Care manual to become familiar with the operation of your room air conditioner. CAUTION Do not lift window sash without holding the unit. The window sash helps keep the unit in the window. Exercise caution when opening the window. Failure to do so many result in personal injury and/or property damage. • Step 7 - Install Unit and assemble Front Grille 1. Push the unit into the installed Chassis. 2. Fasten Base Pan and Chassis with screws to side h

• Be sure to use an exclusive power source. • Contact service man for replacement of power cord. 4 • Step 1 - Prepare Components For Installation Parts for installation are as follows; • SCREW TYPE • Sill Bracket (2 pieces) • Window Kit Left side (Frame ‘L+Shutter) - (1 piece) • Window Kit Right side (Frame ‘R+Shutter) - (1 piece) • Sash Bracket (1 piece) • Frame Guide Lower - (2 pieces) • Levelling Screw (Machine M8x45) - (2 pieces) • 11/4 inch Screw (M5x30) - (4 pieces) • 5/8 inch Screw - (M4x

1. Operate the Selector Switch to run or stop the unit. -Do not use Main Power Switch or Auxiliary Power Switch to operate unit. 2. Do not stick anything into the air outlet or inlet. -It is dangerous and it can cause injury or damage. 3. Avoid exposing your body directly to a continuous cool air - flow for long periods. -It is not good for your health. 4. Do not pour water on the unit to clean it. -It is dangerous and it can cause injury or damage. Never use solvents or harsh chemicals when cle