Évaluations - 5, GPA: 4.2
(
)
)
|
Photos et spécifications Panasonic ES-LF71 |
Facilité d'utilisation
• Wipe off any water droplets on the main body rear terminal. 4 44 Press the SELECT button to select the course. • The “Charge” course starts when attaching the shaver. • Each time you press the SELECT button, the course changes from “Clean/Dry/Charge” “Dry/Charge” “Charge”. • The courses start approximately 6 seconds after they are selected. • The course will be aborted if the power is cut off. In this case, perform the course again from the beginning. • Do not detach the detergent cartridge or the water tank as the cleaning liquid may spill causing a malfunction. ES-LF71_CIS.indb 8 Course 1 Charge Charge 0 to 60 min Clean 10 min • Dry 1 0 min • 2 Clean/Dry/ Charge 3 Dry/Charge Time required (guide) Dry Charge 0 min 0 to 60 min (170 min*) It is not possible to change the course after the “Clean/Dry/Charge” course has started. Charge 0 to 60 min It is possible to change to the “Clean/Dry/ Charge” course even after the “Dry/Charge” course has started. * When the ambient temperature of the self.cleaning recharger is low (approx. 15 °C or lower), the time it takes to dry the shaver increases. • The Clean or Dry function may stop under extreme low temperatures (approx. 0 °C or lower). In such a case, the CLEAN and DRY lamps will blink when the “Clean/Dry/Charge” course is selected, or the DRY lamp will blink when the “Dry/Charge” course is selected. 2011/04/22 15:05:09 English Follow the steps outlined below if the status lamp blinks or glows Blinks Glows Correctly set the detergent cartridge and then restart a course. Remove the shaver from the selfcleaning recharger and then check that the [CLEAN] lamp has gone out. (Be careful as the blade may be hot or wet.) Check that the water tank is correctly attached, the water tank cap is securely closed and the selfcleaning recharger is placed horizontally. If the status lamp goes out Continue a course. When an abnormality has been corrected When no abnormality was found Remove the AC adaptor from a household outlet. It is time to replace the detergent cartridge and cleaning liquid inside the water tank. Wash away the old cleaning liquid and then rinse the water tank and then refill it with water. Replace the old detergent cartridge and then restart the course. When the status lamp goes out When the status lamp glows again Continue a course. Contact an authorized service center. . Cleaning the shaver without the self-cleaning recharger 1. Disconnect the power cord from the shaver. 2. Apply some hand soap and some water to the outer foil. 3. Rotate the lock ring to unlock the power switch. 4. Press the power switch for more than 2 seconds to activate the sonic vibration cleaning mode. The battery capacity lamps blink in order. After about 20 seconds, it will be automatically turned off, or you can turn it off by pressing the power switch. 5. Remove the outer foil section and press the power switch for more than 2 seconds to activate the sonic vibration cleaning mode and clean it with running water. 6. Wipe off any drops of water with a dry cloth. 7. Dry the outer foil section and the shaver completely. 8. Attach the outer foil section to the shaver. 9. Lubricate the shaver. •• 4 5 Drying the shaver with the self-cleaning recharger 1. Attach the outer foil section to the shaver. 2. Dry the shaver with self-cleaning recharger using “Dry/ Charge” course. 3. Lubricate the shaver. ES-LF71_CIS.indb 9 2011/04/22 15:05:09 10 English Lubrication To maintain shaving comfort for a long time, it is recommended that the oil provided with the shaver is used. 1. Switch off the shaver. 2. Apply one drop of oil to each of the outer foils. 3. Raise the trimmer and apply a drop of oil. 4. Switch the shaver on, and run it for approximately five seconds. 5. Switch off the shaver, and wipe off any excess oil from the outer foils with a soft cloth. It is not necessary to oil the blades after cleaning the shaver with the self-cleaning recharger. (Lubricant is included in the cleaning detergent.) • Cleaning with the brush Clean the inner blades using the short brush by moving it in direction (A). Clean the system outer foil, the shaver body and the trimmer using the long brush. Do not move the short brush in direction (B) as it will damage the inner blades and affect their sharpness. Do not use the short brush to clean the outer foils. • • (A) (B) Replacing the system outer foil and the inner blades system outer foil once every year inner blades once every two years Replacing the system outer foil 1. Press the foil frame release buttons and lift the outer foil section upwards. 2. Press the system outer foil release buttons and pull down the system outer foil. 3. Align the foil frame mark ( ) and the system outer foil mark ( ) and securely attach together. The system outer foil cannot be reversely attached. Always insert the system outer foil to the foil frame when attaching to the shaver. 4. After turning the foil frame mark ( ) to the front, securely attach the outer foil section to the shav...
Ce manuel est également adapté pour les modèles :électrique - ES-LF71-K820 (6.38 mb)