Évaluations - , GPA: ( )

Instructions Patton electronic, Modèle PATTON 2621

Fabricant : Patton electronic
Taille : 1.25 mb
Nom Fichier : 2600-SER-GS.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Verify that the proper voltage is present before plugging the power cord into the receptacle. Failure to do so could result in equipment damage. 3. Verify that the AC power cord included with your IPLink router is compatible with local standards. If it is not, refer to chapter 13, “Contacting Patton for assistance” on page 112 to find out how to replace it with a compatible power cord. 4. Connect the male end of the power cord to an appropriate power outlet. 5. Verify that the green Power LED is lit (see figure 13). 6. Unplug the AC power cord from the IPLink Series router to power down the unit. Figure 13. IPLink front panel LEDs and Console port locations (Model 2603 shown) Installing the Ethernet cable Do the following: The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and mechanical serviceability. 1. Connect the DB9-RJ45 adapter to the DB-9 serial port on the PC or dumb terminal. Use the RJ45-RJ45 straight-through cable between the adapter and the red marked RJ45 port on the IPLink Router. 2. Do not connect the router to the Ethernet LAN at this time. 3. On the PC, start a terminal emulation session (such as TeraTerm or HyperTerminal) at 9600 bps, 8 data bits, 1 stop bit, and no parity. 4. Plug the AC power cord into The IPLink Series router to power up the router. 5. Type superuser for Login:, and press Enter. 6. Then type superuser for the password, press Enter. 7. A message will display, “Login Successful.” By typing the character “?”, all the commands will be displayed. Login: superuser Password: ********* Login successful --> 8. Any commands’ parameters may be seen by entering the command followed by a space and a question mark. IP address modification The first parameter to change is the IP address from the default IP address of 192.168.200.10 to your selected IP address. Do the following (comments are in brackets […]): The IP address has now been successfully changed. Web Operation and Configuration Now that the IP address has been configured for your application, you can complete the configuration using any standard web browser. PC Configuration In order to connect the PC to the Ethernet LAN to communicate with The IPLink Series router, the PC’s IP address should be on the same subnet as the router. Connect a straight-through Ethernet cable between the PC’s NIC or PCMCIA Ethernet card and an Ethernet hub or switch. Web Browser Do the following: 1. Launch a standard web browser such as Netscape Communicator or Internet Explorer (IE). 2. Enter the IPLink router’s IP address into the URL or Address field of the browser. To see the IPLink Series router home page, refer to the following Figures. Model 2603 is shown in figure 14. Model 2621 in figure 15. Model 2635 in figure 16. Figure 14. Model 2603 home page Figure 15. Model 2621 home page Figure 16. Model 2635 home page Chapter 4 Ethernet LAN Port Chapter contents Introduction ..........................................................................................................................................................41 LAN Connections ...........................................................................................................................................41 Ethernet Port ..................................................................................................................................................41 Introduction The Ethernet LAN interface/port can be configured with two IP addresses, a primary and a secondary IP address. The configuration web page is found by following the path -> Services Configuration (in the Configuration Menu) -> LAN -> ‘Change default LAN port IP address’ (button on the main window). The Basic and Advanced Port Attributes of the Ethernet LAN port is found by clicking on the Ethernet hyperlink in the IPLink’s Configuration Menu, the narrow window on the left-hand side of the web page. Clicking on the View advanced attributes... hyperlink leads to a webpage with only a few parameters that could be of interest. They are for controlling auto-negotiation, 100BaseT mode, and Full-duplex mode. LAN Connections The default LAN port’s IP address and netmask can be changed on this webpage. Go to -> Services Configuration (in the Configuration Menu) -> LAN -> ‘Change default LAN port IP address’ (button on the main window). (See figure 17.) The primary IP address and mask can be modified here, but if you do, you will no longer be able to access the IPLink’s webpages with the previous IP address. The interface associated with the Ethernet is named ip1. You can also configure a secondary IP address to the Ethernet LAN port. Figure 17. Ethernet LAN port IP address configuration The secondary IP address must be in the same subnet as the primary IP address. With primary and secondary IP addresses, you can reach the IPLink’s webpages via either IP address. However yo...