28190 Manual_Revised_07_0409 Page 20 Deep Cuts The proper cutting depth for each pass is always determined by the material, the cutting bit size and type, and the power of the router motor. Always make several progressively deeper cuts by starting at one depth and then make several passes, each time increasing the cutting; depth until your desired depth is reached. Making a cut that is too deep will stress the router motor and the cutting bit, and it may burn the work piece and dull the cutting

Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine if it will operate properly and perform its intended function. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. A guard or other part that is damaged should be properly repaired or replaced at a Sears Service Center,. 8. INSPECT and remove all nails from lumber before routing. 9, SAVE THESE INSTRUCTIONS.

315.269210 18/32 7/16 13132 Save this manual for future reference oSafety CAU'nON: Read and o Features follow aH Safety RuUes and Operating Rnstructions before oOperation first use of this product. oMaintenance o Parts List Customer HeUp Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Bevedy Rd., Hoffman Estates, RL60179 USA Visit the Craftsman Web page: US 983000-028 FULL ONE YEAR WARRANTY ON CRAFTSMAN PROFESSIONAL ROUTER If this rRRFTSMRN router fails due to a defect in material or workmansh

This feature functions only when using the Craftsman router supplied with this table (model 17541) or the following Craftsman routers: models 17542 and 17543. _, WARNING: If any parts are missing, DO NOT attempt to assemble, install, or use your router table until the missing parts have been found or replaced and your router table has been properly and correctly assembled according to this product manual. • In order to simplify handling and to minimize any damage that may occur during shipping,

On the other hand, if the bit is a large one, the cut is deep or the wood is hard to cut, the proper feed may be a very slow one. A cross-grain cut may require a slower pace than an identical with grain cut in the same workpiece. There is no fixed rule. You will learn by experience from practice and use. The best rate of feed is determined by listening to the sound of the router motor and by feeling the progress of each cut. Always test a cut on a scrap piece of the workpiece wood, beforehand. F

Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman Web page: 983000-435 6-04 • Warranty ................................................................................................................................................................ 2 • General Safety Rules ............................................................................................................................................ 3 • Speci

• USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy duty tool. Don't use tool for purpose not intended --for example --don't use a circular saw for cutting tree limbs or logs. • WEAR PROPER APPAREL. Do not wear loose clothing or jewelry that can get caught in tool's moving parts and cause personal injury. Rubber gloves and nonskid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair and keep it from being drawn into nearby

See Figure 5. CU'I-rERAT ZERODEPTHOF CUT Fig. 6 • Position your router so that the cutter can extend below the subbase for desired depth setting, See Figure 7. DEPTH INDICATOR RING BASE INDICATOR POINT Fig. 8 The depth of cut is readable from both sides of the depth adjusting ring. There is a depth indicator ring and indicator point on both sides of the depth adjusting ring. The bottom ring is convenient when using your router mounted to a router table. The indicator point on the base should als

We hope you enjoy many years of creative and productive use of this product. Trend welcomes comments on this and all our products in our aim to develop and improve what we do to meet the needs of you, the customer. Please contact our Technical Department in the first instance if you have any comments or queries. Trend is the UK's leading supplier of router cutters, equipment and accessories. Our Craft Range of Cutters referred to in this manual, is designed specifically to meet the needs of amat

Plunge Frame ........................................................................................................ 1 Plunge Base .......................................................................................................... 1 Subbase ................................................................................................................ 1 * Screw (#10-32 x 1/4 in. Pan Hd.) **STD511102 ................................................... 3 Plunge Spring .....................