Évaluations - , GPA:
(
)
)
Fabricant : Echo
Taille : 455.43 kb
Nom Fichier : 99944200513e_011309.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
Keep a Firm Grip • Hold the front and rear handles with both hands, with thumbs and fingers encircling the handles. Keep a Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach. Avoid Hot Surfaces • Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation. equIpmenT WARNING Use this attachment with ECHO approved models only. Serious injury may result from the use of this attachment combined with a non approved ECHO product. • Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed. • Inspect shield for damage and that it is securely in place. Replace if shield is damaged or missing. • Check that the cutting tines are firmly attached and in safe operating condition. • The cultivator gear housing is designed for ECHO recommended tines. Do not modify the gear housing for any other purpose or replace tines with other type or size. NOTE ECHO, Inc. will not be responsible for the failure of sweeping devices, accessories, and parts which have not been tested and approved by ECHO for use with this ProPaddle Attachment. WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. • ALWAyS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stopbefore removing obstructions, clearing debris, or servicing unit. • DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit. • NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings. desCrIpTIon Locate this safety decal on your unit. Make sure the decal is legible and that you understand and follow the instructions. If the decal cannot be read, a new one can be ordered from your ECHO Dealer. See PARTS ORDERING instructions for specific information. 1 2 3 4 5 4 6 7 1. DRIVE ShAfT ASSEMBLy - Contains a specially designed liner and the flexible drive shaft. 2. ShIELD -Attached to deflect debris away from operator and reduce accidental contact with tines. 3. hUB - Separately attached to axle ends by clevis pin and spring pin. Tines bolt to hubs. 4. TINES - Identical on right and left side from operator's position. See page 12 for optional settings. 5. GREASE ACCESS BOLT - Apply grease to gear housing every 25 hours of use. 6. GEAR hOUSING - Houses gears and ball bearings for driving tines. 7. SERIAL NUMBER LABEL - Also serves as insertion line when drive shaft is properly engaged. ConTenTs The ECHO product you purchased has been factory pre-assembled for your convenience. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. 1 -PAS Cultivator Attachment -Operator's Manual -Warranty Registration Card -Storage Hook Assembly The ECHO product you purchased has been factory pre-assembled for your convenience. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. 1 -PAS Cultivator Attachment -Operator's Manual -Warranty Registration Card -Storage Hook Assembly assembly WARNING Do not perform maintenance or assembly procedures with engine running. power head shafT/lower shafT assembly Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling. 1. Set Power Head/Shaft Assembly on a level surface. 2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock-out position. 3. Remove vinyl cap from attachment drive shaft. 4. Carefully fit attachment drive shaft assembly into coupler (B) to decal assembly line (C), making sure that the inner lower drive shaft engages into the square upper drive shaft socket. NOTE Earlier model Power Heads may have shorter couplings. Short couplings fit flush to decal point (E). New couplings are 4-3/4 in. long, and fit flush to line (C). A B D E NOTE Lower bearing housing and head assembly must be in line with the engine. 5. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft hole. Insure locator pin is fully engaged by twisting lower drive shaft. Locator pin should snap flush in coupler. Full engagement will prevent further shaft rotation. 6. Secure lower shaft assembly to coupler by tightening clamping knob (D). D C A operaTIon WARNING • When engine starts tines may rotate. Warn fellow workers and keep children and pets from coming nearer than 4.5 m (15 ft.). • Always operate cultivator with both hands. • Always stop engine when transporting unit to or between work areas. • Do not perform maintenance procedures, unclog or clean cultiva- tor tines while engine is running. • Do not operate the cultivator above ground level or near feet. • Do not allow the tines to contact large obstructions which may cause kickback ...