Log:
Évaluations - 5, GPA: 3.6 ( )

Instructions Husqvarna, Modèle 295-6273-01

Fabricant : Husqvarna
Taille : 3.9 mb
Nom Fichier : HO1997_1010000-01.pdf
Langue d'enseignement: svitenfrdenldafi
Aller à la télécharger



Facilité d'utilisation


Make sure the machine is stored safely. • The switch trigger may not be locked when in the start mode. • Never attempt to move the vertical scarifier with ropes or lines of any sort. WARNING! Do not scarify the lawn when wet or slippy. Mown grass is damp and creates a slippery surface, Use stout footwear when using the machine and always ensure №at you have good footing. Ensure that the scarifier is in good condition. Check that the lawn to be scarified is free from stones, sticks and other objects which may be thrown from the machine causing injurÿ to people or damage to the machine. Avoiôtransport over gravel paths or similar. Scarifying of steep slopes can be;:dahgerous. Never scarify up or down a steep slope, always traverse across the slope.. . ASSEMBLING THE HANDLE 1 HANDLE ASSEMBLY (Illus. 2) I * Pre-assemble the lower handle with the screws, washers and nuts supplied. Insert Into sockets, on the machine body and tighten the screws. ■ • Fittheintermediatestrutwiththeselftappingscrews.N.B.! The cable must hang under the strut. • Fit the upper handle ensuring that the cable will not be pinched when the handle is lowered. • Secure the cable with the supplied clips. • Ensure that the support roller is in the transport position, the blades thus clearing the ground during transportation. When starting scarification, lower the support rollers to the ° Position 3 =’ Maximum cutting depth (10 mm) relevant working height. Usually position 3. (Illus. 1) « Position 2 = Minimum cutting depth (3 mm) ° Position 1 =Transport position PRIOR TO START i • Before starting the machine ensure that the blades are not damaged. Ensure that the bearing housing, which isolates the blades, is not damaged. « Before using the machine you should always check that the blades and other underchassis parts are not worn or damaged. Change all blades at the same time to ensure . the rotating parts are balanced. STARTING To start the machine: • Press down on the handle in order to lift the front of the machine up thus keeping the blades clear of the lawn. (Illus. 3) • Press in the locking button on the switch body (2 illus. 1) and press the trigger against the handle (1 illus. IJandthe blade shaft will rotate. • Release the locking button.' IMPORTANT INFORMATION The machine should hot fee-leaned at an angle more ' * than that requMd arid sjnly that part'directed away :. from you. -'y: ' ■ ■ ■' OPERATING ° Raise the handle until the support roller at the ■ front of the machine is in contact with the' ground. Walk forward slowly. Adjust walking speed to the lawn’s condition. Slower walking speed results in a higher cutting rate. If you run into stones or suchlike then press the handle down to to lift the blades clear of the ground. o Handle the electric cable as in illus.'4. WARNING! if an accident occurs fegi the cable is pulled into the blade shaft then release the switch trigger immediately Disconnect the plug at the socket. Have the cabte repaired professionally or buy a new one. .. STOPPING / TRANSPORTING » Avoid frequent starting and stopping ° Release the switch trigger and disconnect the machine from the socket if the machine is to be cleaned or carried. ' ' » Always set the-height adjustment to transport position when not in use. « During transport the handle should be carefullyfolded up. Ensure the cable is not damaged. ° Allow the motor to cool down before packing in a box or crate. MAINTENANCE OF THE VERTICAL SCARIFIER The blades must be kept sharp in order to obtain good results. These are wearing items and must therefore be checked and replaces when \ IMPORTANT INFORMATION V * Check regularly that all nuts, s«rors. atici Boats are well tightened and replace any damaged parts, Only original §par^e fiatts should be used. » Cleaning, maintenance ariiuervice mafcWytiS' clone when the machine is disconnected from the socket. •, Do not wash the machine with water. ’ » Check the cables regularly for wear andageing. .; • Never use the triachine in rainy weather or let St standoutsideintherain: * • * Keep the motor free from grass, leaves and . excess grease Sri order to hiinimiseflre»rtsk." ’ 1 necessary. The electrical equipment on the machine, such as the cable, the on / off switch etc. must be frequently checked from a safety aspect. Any defects discovered must be rectified before use. • Clean with a brush after use. N.B.I Do not wash with water. • Check regularly that the blades have not loosened’. AIR INLET FILTER IMPORTANT INFORMATION The alftintet filter must'be cleaned when required. Use a soft brush to remove dry grass, leaves etc. The filter may be taken out for cleaning with: com- '’'prëssed^ftv'^ - STORAGE Store the machine in a dry place. Prevent rusting by treating all parts with a rustprevention agent. 4 (Illus 5) »11®! DISMANTLING A set of blades for the vertical scarifier consists of 15 blades' and is available from your retailer. The spare part number ...

Ce manuel est également adapté pour les modèles :
Cultivateurs - 1010000-01 (3.9 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories