Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
The shaped front edge of the carriage is comfortable to the operator's body even when leaned on during movement. The carriage lock is standard. Instead of the rolling carriage, model 5212F has a stationary cutting table often used for poultry cutting. Table, carriage, pulleys, guides, and wiper assemblies can be quickly removed without tools for ease of cleaning. Moving parts are enclosed but accessible. The blade is guarded above and below the cutting zone. The pusher plate is provided to eliminate the need of handling items close to the blade; it can ride on the right "flanged-end" of the carriage so you keep your hands away from the cutting edge of the blade. The 5212 and 5212F Meat Saws have a 2 HP motor controlled by a push-pull switch knob located on the front of the saw (Fig. 1). For electrical specifications above 250 volts, a transformer provides a 115 volt control circuit voltage (optional on lower voltages). Thermal overload protection is an option. One long-life blade is furnished with each saw as standard equipment. This blade cannot be resharpened; replacement blades are available through your local Hobart Service Office. PL-40801-1 Head Door Saw Blade Gauge Plate Gauge Plate Adjusting Knob Gauging Pin Hand Knob Gauge Plate Rack Pusher Plate Base Door Legs Feet Carriage Guide Carriage Lock Switch Knob Carriage Support Carriage Table Upper Guide and Guard Slide Rod for Upper Guide and Guard Fig. 1 – 2 – INSTALLATION UNPACKING AND ASSEMBLY Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to make sure it agrees with the specifications on the machine data plate located on the base. Packed in the scrap pan in the base compartment are the pusher plate, feet, and set screws. Place the pusher plate in its storage location under the carriage support (Fig. 1). Remove the four shipping bolts from the underside of the skid. Apply Lubriplate 630AA grease (supplied) to the threaded studs of the four feet; assemble the feet to the legs (Fig. 1). Tilt to one side and install two feet, then tilt the other way and install the two remaining feet. LEVELING Place the saw in its operating location. Using a spirit level, level the meat saw front-to-back and side- to-side by turning the feet in or out. Lock feet in place using set screws furnished. WARNING: DISCONNECT ELECTRICAL POWER AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT. SAW BLADE The saw blade must be installed so the teeth point to the right and down (Fig. 2). UPPER GUIDE AND GUARD ASSEMBLY When the saw is off, the hand knob (Fig. 2) can be used to raise or lower the upper guide and guard assembly so the cutting zone is only as high as necessary for the piece being cut. The hand knob is Upper not loosened during raising or lowering — it should Blade Guard remain tightly secure. UPPER PULLEY WIPER Hand The upper pulley wiper (Fig. 4) is attached to the head Knob by a threaded stud and knob; it wipes the upper pulley and blade during use. HEAD DOOR The head door (Fig. 1) should be installed on the two PL-40777-1 hinge pins and closed during saw use. To remove the head door for cleaning, open the door and lift straight up off the hinge pins. Fig. 2 Upper Back-Up Block Upper Guide – 3 – LOWER GUIDE AND WIPER ASSEMBLY The lower guide and wiper assembly fits in the slideway of the wiper bracket (Fig. 3). The blade fits in the slots of both the steel guide and the nylon guard. Wipers fit on both sides of the blade. This assembly includes a wiper for wiping the lower pulley during use. TABLE In use, the table is aligned and supported by the locator block (Fig. 3) and four table rests (Fig. 4) fastened to the machine base. When aligned properly, the table is secured to the base when the tongue of the table is inserted in its slot (Fig. 4) and the table clamp is latched down (Fig. 5). To remove the table, raise the gauge plate to its vertical position. Release the table clamp on the left side. Shift the table to the left, freeing the tongue from its slot. Lift table by its front side to remove. To reinstall the table, tilt the front side of the table up so the rectangular hole on the rear side goes around the base of the column. Lower the table to the base. Raise the left end of the table and slide it to the right so the tongue on the right side fits in its slot. Lower the left end of the table. Align so the pins of the table rests are outside of the table support angles. The rectangular hole in the front table support angle straddles the locator block. When the table is in proper position, latch the table rod with the table clamp (Fig. 5). Fig. 3 PL-40790-1 Nylon Guard Blade Guide Locator Block Lower Pulley Wiper Wipers Blade Slideway - Wiper Bracket Lower Guide and Wiper PL-40786-1 Upper Pulley Pulley Latch Slot for Tongue of...