Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
2006) Installation, Operation and Care of MODEL 6430, 6430T, 6460 & 6460T PEELERS SAVE THESE INSTRUCTIONS GENERAL Models 6430 and 6430T Peelers are designed to peel 30 to 33 lbs (13.5 to 15.0 kg) of product in 1 to 3 minutes using a 3/4 HP, single- or three-phase electric motor. The 6430T includes a synchronous timer and is available for single-phase electrical service ONLY. Models 6460 and 6460T Peelers are designed to peel 50 to 60 lbs (22.5 to 27.0 kg) of product in 1 to 3 minutes using a 1 HP, single- or three-phase electric motor. The 6460T includes a synchronous timer and is available for single-phase electrical service ONLY. All models incorporate a reinforced peeling disc with the abrasive permanently bonded to its surface and a Lexan Liner for the inside of the hopper. The switch or timer is mounted on the right side of the discharge chute as standard but can be ordered on the left or changed in the field. The bottom of the peeler unit is cushioned with a rubber trim molding which also provides a seal. Optional accessories include a peel trap or disposer stand. INSTALLATION NOTE: Immediately after unpacking, machine should be checked for possible shipping damage. If the machine is found to be damaged after unpacking, save the packaging material and contact the shipper. This machine MUST be cleaned after installation and before being put into service. Refer to MAINTENANCE for instructions. PEELER UNIT (FIG. 1) 1. Remove the peeler from its shipping carton and remove the hopper top. 2. Remove the fill tube and bracket assembly from the peeler housing and the cloth bag containing the fill tube gasket and acorn nuts. 3. Do NOT remove the rubber molding on bottom of peeler. 4. Lay the peeler on its side. Slightly loosen the clamp that attaches the drain hose and pull the drain hose down so that it extends approximately 7/8" below the bottom of peeler housing. Tighten the clamp. On units that will NOT use a peel trap or disposer stand, attach the bottom cover plate using the bolts and washers supplied with the unit. – 2 – LOCK WASHER LOCK WASHER FLANGE PL-56337 DATA PLATE INLET TUBING SWITCH HOPPER TOP BRACKET ASSEMBLY SCREW TUBE COUPLING ABRASIVE DISC JUNCTION BOX COVER CONDUIT HOLE RUBBER MOLDING HARDWARE JUNCTION BOX DISPOSER SWITCH PEELER PEEL TRAP DISPOSER STAND DISPOSER AND WASHER PEEL TRAP ADAPTER DRAWER PLATE DISPOSER Fig. 1 – 3 – LEXAN LINER LEXAN LINER Slide the liner (Fig. 2) into the hopper, ensure the liner is under retaining brackets (Fig. 2) and resting on the top of the lip (Fig. 2) on the bottom of the hopper chamber. PL-41652-1 LINER RETAINING BRACKETS LIP PL-41653 KEEPER Fig. 2 Fig. 3 2. Push the liner keeper into the hole (Fig. 3) provided. 3. Secure the keeper using the exterior latch. PEEL TRAP If a peel trap is to be used, unpack the trap from its shipping carton. Remove the legs and cloth bag from inside the peel trap. The cloth bag contains hardware for attaching the legs. Legs It will be necessary to remove the peel trap drawer (Fig. 1) to allow enough room for attaching the legs. – 4 – Assemble the legs as follows (Fig. 4): Assemble the legs as follows (Fig. 4): Lay the peel trap on its side. 2. Assemble one of the rubber gaskets to one of the curved leg clamp bolts. 3. Assemble the bolt and gasket from the inside, through one of the leg bolt holes in the peeler housing. 4. Assemble a leg and a leg slot cover on the leg clamp bolt. 5. Place a stainless steel washer and acorn nut onto the clamp bolt and partially tightened, set unit upright. 6. Each leg has an upper and lower leg clamp bolt assembly. When all are assembled and partially tightened, set unit upright. 7. Adjust each leg to a suitable height such that the unit is level, and tighten the acorn nuts. PL-41651-1 LEG RUBBER GASKET CLAMP BOLT SLOT COVER WASHER ACORN NUT Fig. 4 Peelers The peeler may be positioned on the peel trap in one of four positions. Each of the positions will cause the peel trap drawer to be located in a different position relative to the discharge chute. The peel trap drawer may be directly beneath the discharge chute, to the right, left or rear (see Fig. 5). After selecting the most convenient position for the peel trap drawer, remove the cover disc from the appropriate hole in the peel trap top and position the peeler on top of the peel trap, with the peeler drain hose extending through selected hole (Fig. 5). The cloth bag shipped in peel trap drawer contains the capscrews, lockwashers and washers (Fig. 1) necessary for fastening the peeler to peel trap. CAUTION: Excessive tightening of screws may distort housing. If desired, the peel trap legs may be bolted to the floor. – 5 – RELATIONSHIP OF PEELER WITH TRAP VIEW OF TOP OF PEEL TRAP To position peel trap drawer BENEATH the discharge chute: To position peel trap drawer to the RIGHT of discharge chute: To position peel trap drawer to the LEFT of discharge chute: To position peel trap drawer to the REAR of discharge chute: Discharge Chute Dischar...