Évaluations - 4, GPA: 3.8
(
)
)
|
Facilité d'utilisation
Storage lid (model FP2500SC) (Part # FP2500S-09) † 6. Dough blade (Part # FP2500-10) † 7. Large, stainless steel chopping blade (Part # FP2500-03) † 8. Disc stem (Part # FP2500-11) † 9. 10-cup processing workbowl (Part # FP2500-06) 10. Base 11. Cord wrap (under base) † 12. Non-skid suction feet (Part # FP2500-12) 13. Controls † 14. 3-cup processing workbowl (Part # FP2510S-13) † 15. Small, stainless steel chopping blade (Part # FP2510S-04) † 16. 3-cup processing workbowl cover (Part # FP2510S-07) † Consumer replaceable/removable parts 3 How to Use This product is for household use only. • Remove all packing material and any stickers from the product. Important: Handle chopping blades and slice/shred disc carefully. They are very sharp. • Wash all removable parts as instructed in CARE AND CLEANING section of this manual. • Select a level, dry countertop where the appliance is to be used, allowing air space on all sides to provide proper ventilation for the motor. ASSEMBLING THE PROCESSOR HOW TO INSERT AND REMOVE THE CENTER POST: The center posts of both bowls are removable: 1. Turn the bowl upside down. 2. Grasp the clear outer tabs and turn the center post clockwise until the lower tabs are free. Lift the post out (B). 3. To return to its original position, place center post into smaller opening in bottom of workbowl and turn counterclockwise until tabs snap into place. HOW TO LOCK THE LARGE AND SMALL WORKBOWLS IN POSITION: 1. Attach center post to workbowl. Place the workbowl on the base with handle turned to the right of the locking mechanism (C) over the unlock symbol . 2. Hold handle and rotate workbowl clockwise toward the lock symbol until it clicks firmly into place (D). Be sure to lock the workbowl in place before attaching the blades and cover. HOW TO LOCK THE COVER: 1. Place cover over workbowl with the small latch to the right of the workbowl’s handle (E). 2. Hold feed chute of workbowl cover and rotate cover clockwise until cover locks into place. B C D 4 E Important: For your protection this appliance has an interlock system. The processor will not operate unless the workbowl, cover and wide-mouth feed chute are properly locked in place. 3. If using the large workbowl, place the wide-mouth feed chute on top of the cover with the small tab to the right of the workbowl’s handle. Turn clockwise until it clicks into position over the handle. 4. Insert the food pusher into the central tube of the wide-mouth feed chute. Turn clockwise to lock in place. The pusher is used to guide foods through the feed chute and can be removed when adding liquid or additional foods while the processor is running. To remove, turn counterclockwise. CONTROLS The controls are located on the front of the base (F). Press PULSE (P), HIGH or LOW to select a function (see directions below). OFF/PULSE: • Processor should be stored in OFF position and unplugged when not in use. • Use PULSE (P) for short processing tasks. This lets you control the size and uniformity of foods being chopped. • The OFF/PULSE (O/P) button must be pressed and held for the appliance to operate in PULSE mode. When released, the appliance will stop. • The motor of the processor will run as long as the OFF/PULSE (O/P) button is held down. Press the button and then release to allow the blades to stop running and the food to fall to the bottom of the workbowl. • Pulsing gives better control when chopping, mincing, mixing and blending foods. You can control the size of the foods, from coarse to fine. HIGH and LOW: When either speed is selected, the processor will run continuously until the OFF/ PULSE (O/P) button is pressed. HOW TO CHOP IN THE LARGE OR SMALL WORKBOWL: The chopping blade is used to coarsely or finely chop, mince, mix and puree foods to a smooth consistency. 1. Lock workbowl into position (see Illustrations B and C). 2. Hold chopping blade by center shaft and insert onto center post (G). Caution: The blade attachments are very sharp. Use caution when handling and storing. 3. Place food in workbowl. 4. Place cover on workbowl and lock into place by rotating clockwise (see Illustration D). 5. When using large workbowl, place the wide-mouth feed chute and food pusher in place. Important: Never use your fingers to direct food through the chute. 6. Select your desired speed (PULSE (P), LOW or HIGH). Note: Process foods for no more than a few seconds at a time. Pulsing produces excellent results and offers greater control. 7. If using small workbowl, press OFF/PULSE (O/P) and wait for blades to stop revolving. If using large workbowl, food can be added while processor is running; remove food pusher and insert food through the feed chute. Replace food pusher in chute. Important: Be sure chopping blade has completely stopped spinning before removing cover from processor. 8. Press the OFF/PULSE (O/P) button and allow blades to stop revolving before removing cover. Twist cover toward to remove. 9. Unlock workbowl by turning it counterclockwise and lif...