Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Use the following operation to replace the corner cutter tray when necessary. Corner Cutter Tray (Corner cutter tray CC-1) (1) Remove the corner cutter tray as illustrated. (2) Install the new corner cutter tray. Note Use Brother authorized cutter units (SC-2 or CC-1) only. Other cutter units, (top/bottom cutter unit and the upper blade of the corner cutter) are not replaceable. Please consult your dealer if these cutter units become damaged. -31 Troubleshooting Problem Cause Solution No activity after the machine has been turned on. The AC adapter is not connected properly. Check that the machine is plugged into a power source. The top cover is not completely closed. Close the top cover. The document will not feed into the machine and alert buzzer sounds (two times). The document was not set properly. Reset the document properly and press Start again. The document is too thick or too thin. The minimum and maximum thickness of paper that can be used with this machine are 0.1mm-0.2mm. The document is wrinkled or curled. Curled, wrinkled documents cannot be laminated. The width of the document is too narrow or too wide. The width of the document must be between 2.2” (55mm) and 8.5” (216mm). Job stops during processing, the Start button blinks (in red) and the alert buzzer sounds. The document is too small. Documents must be at least 3.5” (90mm) long. The wrong film cartridge is installed. (US Letter/A4 paper cannot be laminated when a 4.8 inch/A6 film cartridge is installed in the machine.) Install the proper film cartridge. The length of the document is too long. The length of the document must be less than 39.4” (1000mm). The film has run out. Change the film cartridge. The document is jammed. Remove the jammed document. Job stops during processing, the Start button blinks in orange. Document length is more than 13.8” (350mm) long. Press Start to restart the process. Output quality is poor. The document is too thick or too thin. The minimum and maximum thickness of paper that can be used with this machine are 0.1mm - 0.2mm. The document is wrinkled or curled. Curled, wrinkled documents cannot be laminated. The document is too small. Documents must be at least 2.2” (55mm) wide and 3.5” (90mm) long. The document will not feed straight. The document guide is not set properly. Set the document guide properly. The document is not cut after processing. The cutter units are not installed properly. Check if the cutter units are installed in the machine properly. The thickness of the paper is too thick. The maximum thickness of paper that can be used with this machine is 0.2mm. The cutter units have been damaged. Replace the cutter units. You can replace the side cutter units and corner cutter tray. It is not possible to replace the top/bottom cutter. If these cutter units do not work properly, please consult your dealer. Auto Cut Mode Off is selected. Change the setting of the Auto Cut Mode selector switch. The cutting position is not accurate (top/bottom) The paper sensor is damaged. Please consult your dealer. Stickers will not stick. Sticker film has not been loaded. Use Brother Sticker Film Roll LC-A9 or LC-A5. The liner of the sticker has not been peeled away. Remove the liner. The surface that the sticker is meant to adhere to is dirty or rough. Wipe the surface or try another surface. The Start button blinks (in red) and the alert buzzer sounds when the machine is turned on. The film cartridge is not installed properly or an incompatible film cartridge is installed. Install the film cartridge properly. Use Brother authorized film cartridges and film refills only. The proper AC adapter is not being used. Use a Brother authorized AC adapter. The Start button blinks (in red) and the alert buzzer sounds when the top cover is closed The film cartridge is not installed properly or an incompatible film cartridge is installed. Install the film cartridge properly. Use Brother authorized film cartridge and film refills only. -32 Specifications Model number: LX-900/LX-910D Processing method: Cold pressure method Power supply: AC adapter (included) USA 120V±10% (60Hz) Output DC 18V 700mA Min./max. width of document: 2.17” – 8.50” (55mm – 216mm) Min./max. length of document: 3.54” – 39.4” (90mm – 1000mm) Min./max. thickness of document: 0.004” – 0.01” (0.1mm – 0.2mm) Film: Refillable cartridge film Film type: LC-D9 (9.0”/A4 width double-side laminate) LC-A9 (9.0”/A4 width adhesive-back laminate) LC-M9 (9.0”/A4 width magnetic-back laminate) LC-D5 (4.8”/A6 width double-side laminate) LC-A5 (4.8”/A6 width adhesive-back laminate) LC-M5 (4.8”/A6 width magnetic-back laminate) Max number of output/cartridge: LC-D9/A9: About 60 sheets 11.7”/A4 paper LC-D5/A5: About 100 sheets7”/A6 paper LC-M9: About 12 sheets 11.7”/A4 paper LC-M5: About 20 sheets 7”/A6 paper Document feed speed: 0.75”/sec. (19mm/sec.) Cutting system: Built-in cutting system with paper size detection Side cutter units (replaceable) Top/bottom cutter unit (non-rep...
Ce manuel est également adapté pour les modèles :Laminator - LX-910D (443.1 kb)