Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
(Figure 3) 10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). (Figure 4) 11. Reinstall the Feed Table and the Frame-Paper Guide,and close the Safety Cover. 12. Adjust the nip setting to appropriate gap. 13. Insert and push the leader board until they reach the front nip point. 14. Push the Run button. 15. Push the leader board into the rollers. (Figure 5) Figure 5 16. Adjust the top and bottom tension knob by rotating it clockwise or counterclockwise. Turn it until the top and bottom roll films have some resistance varies (the tension depending on the film thickness; the thicker the film the more tension is required). (F'gure 6) Figure 6 Figure 3 Figure 4 12 ¿RS§s£™9„ 17. Press the Stop button when the leader board has completely exited from the rollers. 18. Use the Cross Cutter to cut the leader board from the web (see page 9). 19. Set the nip setting to the appropriate position for the Over-lamination / Decaling application. 12.2. Mounting 1. Lay the decaled image face down on a flat surface. Carefully peel back and put a crease along the edge of the release liner ( Approximately 1 in or 25mm, Figure 1). 2. With the image facing up, align the image onto the board. Press firmly from the center out (Figure 2). 3. Adjust the pressure lever to ensure the proper opening (Figure 3). Figure 2 Figure 3 13 RSC Series 4. Flip the image over the top roller and hold on to the release liner (Figure 4). Figure 4 5. Press the foot pedal once, and then let it go while slowly pulling the release liner as the board enters the main roller nip (Figure 5) 6. Press the foot pedal once again when the board has completely exited from the rear of the unit. Trim the board if necessary. 14 ¿RSËArign 13. INSTALLATION OF FRONT FEEDER and REAR REWINDER OPTIONS Note: Below options are to be installed by an authorized RS reseller. Installation of the Front Feeder Option (Includes 2 brackets, one spindle, and mounting hardware). 1. Install the Front Feeder to the inside of the front frames using four 1/4"(M6) hexagon bolts on each side (Figure 1) Figure 1 Installing the Rear Rewinder Option (Includes motorized winder, bracket, one spindle, and mounting hardware). 1. Remove the left and right covers by using a Phillips screwdriver (four screws on each side cover) (Figure 2 & 3). 2. Remove the lever knob screw and lever (Figure 4). 3. Remove the rear cover by removing all 10 screws (4 top, 4 bottom, and 1 on each side) (Figure 5 & 6). Figure 5 Figure 6 Figure 2 Figure 3 15 RSC Series 4. Disassemble the power switch bracket and place the left rewinder outside of the frame; fasten with round head 3/16"(M5) screws (included in the option kit). Then, reinstall the power switch bracket (Figure 7). 5. Install the right rewinder on the outside of the frame and connect the motor wire connector to the rear wire (Figure 8 & 9). Figure 7 Figure 8 Figure 9 6. Reinstall the rear cover. 7. Reinstall the side covers. 8. Reinstall the lever knob and screw. 16 ¿RSË&rign 14. MAINTENANCE Cleaning the Body of the laminaor 1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean. Removing Adhesive Build Up 1. Remove the film from the laminator. 2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the Teflon (metal) and silicone rollers. Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface.Do not use sharp metal objects, steel wool, or abrasives, as these may also damage the rollers. Lubrication 1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever comes first. 15. TROUBLESHOOTING Problem Cause Solution Machine will not turn on: a. Power plug is not plugged in. b. Power switch is in “0” (Off) position. c. Tripped circuit breaker. d. Blown main power fuse. a. Plug the power cord into appropriate outlet. b. Put the power switch to the “I” (On) position. c. Reset the circuit breaker. d. Replace the fuse. There is power, but the rollers are not turning after the “RUN” button is pressed: a. Emergency switch (es) is (are) engaged. b. Paper guide is not installed correctly. c. Blown motor fuse. a. Disengage the emergency switch (es). b. Properly install the paper guide so that the micro switch is activated. c. Replace the motor fuse. The unit is not heating up: a. Did not raise the temperature. a. Raise the temperature. Curled lamination: a. Upward curl. b. Downward curl. a. Loosen the top roll film tension. b. Loosen the bottom roll film tension. 17 RSC Series 16. SPECIFICATIONS X o 10 CO I o
Laminator - RSC Series (4.41 mb)
Laminator - RSC-1650 (4.41 mb)