Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
M9004-593 DCR 27634 refers MAGICARD Sicura Laminator Page 1 Quick Start Guide Ultra Electronics Card Systems Setting up your Sicura Laminator takes just two easy steps: 1. Unpack and install the laminator A Preparing a Location for the Laminator B Removing the Laminator from the Box C Check the Package Contents D Install the Lamination Film E Connect the Laminator to a Power Supply F Set the Optimum operating temperature and test the Laminator Operation G Interfacing to a Rio/Tango printer Important Note for Setting Up your Rio/Tango Printer Driver to work with the Sicura Laminator H Interfacing to a Turbo series printer 2. Stand-alone Mode I Operation of the Hopper J Adjusting the Hopper K Error Indicators 3. Verify correct operation L Important Cleaning Procedures M In Case of Difficulty Note: The Ultra WEB site at contains comprehensive technical support information including the latest downloadable software, WINDOWS Drivers, Technical Bulletins etc Conventions Throughout this guide, the following conventions are used to identify important information. WARNING -Warning messages indicate where personal injury could result from not following the correct procedures. CAUTION -Caution messages indicate where damage to equipment could result from not following the correct procedures. NOTE -Notes convey important information that is identified within the text. Page 2 MAGICARD Sicura Laminator Ultra Electronics Card Systems Quick Start Guide Preparing a Location for the Sicura Laminator and Printer A Location Requirements for your laminator/printer: • A clean, level surface. • An adequate power supply. • Adequate space for: • Ambient temperature +10 to +30 deg C. - opening the printer cover • Relative Humidity 20/70% RH. – opening the laminator cover • Protection from direct sunlight and – cable access at the rear and RH side chemicals. – allowance for air circulation. • Protection from abrupt temperature • An adequately ventilated room. changes. MAGICARD Sicura Laminator Page 3 Quick Start Guide Ultra Electronics Card Systems Removing the Laminator from the Box B Place on a smooth, level surface and remove the polyethylene container. Carefully open the box and remove any accessories. Page 4 MAGICARD Sicura Laminator Ultra Electronics Card Systems Quick Start Guide Checking the Package Contents C The MagiCard Sicura Card Laminator A Roll of Lamination Film and a Take-up Core (only supplied when ordered with the Laminator) Envelope containing this Quick-Start guide A Power Cord with Molded Plug for your country’s voltage standard MAGICARD Sicura Laminator Page 5 Quick Start Guide Ultra Electronics Card Systems Check that the Mains Supply Voltage is correct for your country. (Different models are manufactured for each supply voltage.) Page 6 MAGICARD Sicura Laminator Ultra Electronics Card Systems Quick Start Guide Install the Lamination Film D Lift the transparent cover and move the roller lever to the OPEN position. Turn the fastener . turn counterclockwise and remove the plate. Gently install the roll of film between the rollers. The black alignment marks on the film should be innermost. Ensure that the film passes between the forks of the optical sensor. MAGICARD Sicura Laminator Page 7 Quick Start Guide Ultra Electronics Card Systems Replace and fasten the film retaining Gently turn both rolls, to ensure that plate, and close the lever. there is no slack film. Close the transparent cover. Page 8 MAGICARD Sicura Laminator Ultra Electronics Card Systems Quick Start Guide Connect the Laminator to a Power Supply E Check that the Laminator operating voltage is correct for your supply voltage. (Units cannot be changed from one voltage to another.) Connect to the AC supply and switch ON. Check that the temperature Controller’s LED’s flash. After a few seconds, the display will indicate the temperature of the laminating roller in °C, which will begin to increase in value. MAGICARD Sicura Laminator Page 9 Quick Start Guide Ultra Electronics Card Systems The temperature will achieve the set point level after a delay of 4 minutes, and the READY indicator will illuminate. Notes: 1. When switched on, the laminating roller and take-up roll turn for 30 seconds or until a black alignment panel is found by the optical sensor. 2. The Ready LED will flash for 4 minutes until the roller has heated up, cards cannot be fed in until then. 3. Opening the roller lever will stop all card/film movement. Closing the lever performs a Reset function but without the 4 minutes delay. Page 10 MAGICARD Sicura Laminator Ultra Electronics Card Systems Quick Start Guide Select the Operating Temperature and Test the Laminator Operation F NOTE: The optimum roller temperature is best determined by trial and error, using your own cards and laminating film. The following notes are for your guidance only. • Cards with large, unprinted white areas require a higher temperature for lamination. • We recommend that lamination i...