Évaluations - 3, GPA: 5
(
)
)
|
Facilité d'utilisation
See "Carburetor Adjustment" in the unit Operator's Manual. * WARNING! DO NOT INSTALL BLADES ON GT (CURVED SHAFT) MODEL TRIMMERS ** Arbor diameter of Upper Blade Plate must match arbor diameter of metal blades. *** New cotter pin required each time blade is installed. **** Brushcutters over 16.5 lbs (7.5 kg) dry weight (weight w/o fuel) require a double shoulder harness contents 1 U-handle assembly 1 Lower u-handle bracket (2 halves) 1 Harness clamp w/ring 1 5 x 12 mm bolt 1 8 x 55 mm bolt 1 Circular washer 1 Square nut 2 Throttle cable clips 3 5 x 30 mm bolts w/washers 1 Shoulder harness 1 Hip pad X750011731 X7502234701 10/09 U-Handle Kit installation instrUctions installation Tools Required: 8mm x 10mm Open End Wrench, 19 mm wrench 4 mm hex wrench, screwdriver 1. Close choke and remove air filter and cover. 2. Disconnect ignition stop leads (A) and (B). 3. Loosen nuts (C) and remove throttle linkage from carburetor bracket. 4. Remove inner throttle cable from carburetor swivel (D). 5. Loosen the two (2) drive shaft clamp bolts (E) at engine drive shaft clamp, and remove center drive shaft location bolt (F). 6. Pull drive shaft assembly from clutch case. 7. Loosen two (2) rear handle screws (G) and pull rear handle from the drive shaft assembly. 8. Loosen two (2) screws (H) and remove front handle. A B A B D C F E E H G U-Handle Kit installation instrUctions 9. Insert square nut (I) in lower handle bracket (J) and place bracket on drive shaft 400mm (15 3/4 in.) from engine end of drive shaft. 10. Secure with lower handle bracket clamp (K) and three (3) 5mm x 30mm hex socket bolts. 11. Position harness clamp (L) 220 mm (8-5/8 in.) from engine end of drive shaft assembly. Install 5x12 mm bolt, but DO NOT tighten at this time. 12. Carefully fit drive shaft assembly to engine making sure inner drive shaft engages into clutch socket. 13. Turn drive shaft housing until locating hole lines up with location hole in clamp and install center drive shaft location bolt (F). NOTE Gear Housing must be aligned properly with engine. Aligning center locating hole in driveshaft housing with center drive shaft bolt (F) provides correct alignment. 14. Tighten two (2) drive shaft clamp bolts (E) securely. 15. Install upper U-Handle and bracket on lower bracket and secure with one (1) 8 mm x 55 mm bolt (M) and large circular washer. 16. Route throttle linkage and ignition lead assembly behind U-Handle bracket and clip to drive shaft as shown. I J K K J 400 mm (15-3/4 in.) 220 mm (8-5/8 in.) L ENGINE END F E E M U-Handle Kit installation instrUctions 17. Place inner throttle cable in large hole of carburetor swivel (D). 18. Loosen nuts (C) and place threaded end of throttle linkage in bracket slot. Finger tighten nuts (C). 19. Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly. If adjustment cannot be achieved with adjusting nuts (C), consult with your Echo Dealer for correct adjustment procedure. Tighten nuts (...
Ce manuel est également adapté pour les modèles :Jig Saw et - U-HANDLE SRM-280S (488.77 kb)
Jig Saw et - U-HANDLE SRM-280 (488.77 kb)