Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. General information In these operating instructions, this symbol indicates points of particular importance to safety. The instructions at these points must always be observed in order to avoid the risk of serious injury. 1^1 Caution: high voltage D The numbers refer to the illustrations. The illustrations can be found on the fold-out cover pages. Keep these pages open while you read the operating instructions. In these operating instructions, the power tool to which these operating instructions apply is referred to as "the tool". WSR1000 operating controls D O Blade clamp / blade holder 0 Stroke rate regulator Q Switch interlock Q Control switch Component parts D 0 Type plate Q Motor 0 Gearing section Q Front-end grip area 0 Clamping lever © Contact shoe © Saw blade Contents_Page General information 7 Description 7 Technical data 8 Safety precautions 9 Preparation for use 10 Operation 10 Sawing 10 Blades and accessories 11 Care and maintenance 11 Warranty 11 Disposal 12 Troubleshooting 12 Declaration of conformity See cover Description The WSR 1000 is an electrically powered tool for cutting wood, metal, plastics and composites. It is intended for professional use. The following items are supplied: electric tool, operating instructions, saw blade, toolbox. rTTlThe following conditions must always be observed l^lwhen the tool is in use: - The tool must be connected to an alternating current electric supply in compliance with the information given on the type plate. - The tool is for hand-held use only. - The tool must not be used in places where the surrounding conditions may present a risk of explosion. 7 Main features of the tool Class II electrical protection (double insulated) 0 (as per EN 50144) Anti-vibration system (additional operator protection) Mechanical slip clutch (additional gearing protection) Vibration-absorbing grip Keyless blade clamp Saw blade inversion possible Keyless contact shoe adjustment Infinitely variable stroke rate preselection with speed control switch Right of technical changes reserved The tool is designed for the following uses Applications Range of uses Cutting wood Cutting openings for door and window frames Cutting wood with embedded nails and screws Cutting squared timber up to 220 mm thick Cutting composites (wood, insulation material, metal) Cutting softwoods and hardwoods Rip sawing of materials in sheet form Cutting concrete forming components to length and to size Cutting metal Cutting metal pipes of up to 35 mm dia. to length Cutting plastic pipes of up to 150 mm dia. to length Cutting openings in metal and plastic pipes Cutting composites to length (wood, insulation material, metal) Demolition Cutting through metal and plastic pipes Cutting through cable trays, ventilation ducts and installation channels Cutting up sheet metal and sheet metal trays Cutting through gas concrete blocks Cutting drywall / plasterboard panels Technical data WSR 1000 Nominal power ratinq 1000 W Nominal voltaqe * 110V 220V 230V 240V Nominal current input * 11.7 A 5.6 A 5.4 A 5.2 A Mains frequency 50-60 Hz Weiqht of tool 3.95 kg Dimensions (lxwxh) 570x90x140 mm Stroke rate 500-2950/min. Stroke 32 mm Stroke rate regulation Variable stroke rate, 4 stroke rate settings Blade clamp Keyless, for standard V2" blades Noise (pressure) level < 92 dB (A) Typical vibrational acceleration (weiqhted) < 5.0 m/s2 under no load Orbital action Selectable * The tool is offered in different versions for various mains voltages. Please refer to the information on the type plate for the nominal voltage and nominal current input of your tool. 8 Al Safety precautions When using electric tools, the following fundamental safety precautions must always be observed in order to avoid the risk of injury, electric shock and fire hazards. Please read and observe the instructions below before using the tool. 1. Use protective equipment. (DO© 7. Use the tool only for the purposes for which it is intended. Do not force small tools or attachments to do thejob of a heavy duty tool. Do not use tools for purposes not intended; for example, do not use circular saws to cut tree limbs or logs. âS Wear ear Wear goggles Wear protective Wear respiratory protection gloves protection when the work causes dust 2. Wear suitable working clothing. Don't wear loose clothing, loose long hair orjewellery as it can become caught up in moving parts of the electric tool. Wear non-slip shoes. 3. Make the working area safe. Objects which could cause injury should be removed from the working area. Ensure that the area is well lit. When working, keep other persons outside the range of the tool you are using. 4. Take the influences of the surrounding area into account. Don't expose the tool to rain or snow and ...