Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Feed the saw hard enough to keep it working without much decrease in speed. Forcing it beyond this makes for rough cuts, inaccuracy, and overheating of the motor. Should your cut begin to go off the line, don’t try to force it back on. It's best, of course to make errors on the waste side of the line. Then you can withdraw the saw, sight anew, and start a new cut a trifle inside the wrong one. In any event, withdraw the saw if you must shift the cut. Forcing a correction inside the cut can stall the saw and perhaps spoil the work. IF SAW STALLS, RELEASE THE TRIGGER, DISCONNECT PLUG FROM TOWER SUPPLY AND THEN BACK THE SAW UNTIL ST IS LOOSE, IE SURE BLADE CLEARS THE WORK BEFORE RESTARTING CUTTING. As you finish a cut, release the trigger and allow the blade to stop before lifting the saw from the work. As you lift the saw the spring-tensioned telescoping guard will automatically close under the saw, Remember the blade is exposed until this occurs; never reach under the work for any reason whatsoever. When you have to retract the telescoping guard manually (as is necessary for starting pocket cuts) always use the retracting lever. POCKET CUTTING SAW ACCESSORIES Adjust saw base (shoe) so blade cuts at desired depth. Tilt saw forward and rest front of base . on material to be cut Using lever* retract blade guard to an upward position. Lower rear of base until blade teeth almost touch cutting line. Now release the blade guard and its contact with the work will keep it in position to open freely as you start the cut Start the motor and gradually lower the saw until its base rests flat on the material to be cut Advance saw along cutting line until cut is completed. Release trigger and allow blade to stop completely before withdrawing the blade from the material. When starting each new cut, repeat as above. Never tie the Wade guard In a raised position. BRUSHES Ш Carbon motor brushes should be inspected frequently for wear. To inspect brushes, FIRST, UNPLUG SAW FROM POWER SUPPLY. Then, with a screwdriver, slide the brush cover plates outward and the brush spring will pop out Put the spring, with attached wire extended, out of the opening into the .position shown above and tilt the saw so the carbon brush will drop out of the opening. If the brush is worn down to the grooved line on its side, a new brush is needed and can be obtained from any of the locations shown on the next page. To reassemble, insert brush with worn end toward motor, or a new brush with longest distance from end to grooved line toward motor. Next, insert the small brass plate behind the brush, and then feed in the spring until the round spring cap fits flush with the opening. This allows the cover plate to be pushed back into the closed position. IIP FENCE The lip Fence permits fast, smooth rip-cuts without penciled lines. To Install, insert lip Fence in front slots, set Fence at desired distance from blade and tighten screw. The Rip Fence may also be inserted from the opposite side of the base slots. Cat, No. 51584 SAW PROTRACTOR Guides accurate cross cuts at any angle from 0® to 90®, Calibrated In degrees. Has adjustable pointer. Cat. No. 49531 CUT-OFF GUIDE One-piece guide for making accurate 90® or 45® cuts. Cat. No. S5S82 SAW BLADES Black & Decker manufactures a complete line of' blades which are available from your dealer. These include STANDARD BLADES in the four most popular types: Combination (crosscut & rip), Crosscut, Framing, and Plywood. Chromium plated "PREMIUM QUALITY" BLADES are available in the following types: Combination, Planer, Flooring, Carbide-Tipped, Metal Cutting, Plywood, Friction, Crosscut, and Rip. TEFLON-S* BLADES, having a self-lubricating surface, are made in the Combination and Plywood types. LUBRICATION Your tool was properly lubricated before leaving the factory. It is recommended that, at least once a year, you take or send the tool to a B&D Service Center for a thorough cleaning, inspection and lubrication of the gear case. *Reg. U.S. Pat. Off. by DuPont...
Ce manuel est également adapté pour les modèles :Jig Saw et - 3007 (3.14 mb)