Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
install three Clips (furnished with Guard) 90° apart starting with one Clip at the end of the Guard as shown. LONG END of Clip facing AWAY from you. BELT GUARD _ N LONG END CLIPS 2. Reinstall Motor Pulley the same way it waswhen you aligned the Belt, 3. Place Belt on Saw Pulley. Insert end of Bell through opening in END of Guard. 4. Slip Belt over Motor Pulley. BELT 5. Press Guard onto Support sothat bottom of Guard is approximately 3/4 inch away from Belt. NOTE: To remove Guard, lift up on LONG TABS of Clips, pull Guard outward. The Clips should remain on the Belt guard Support. 3/4 iN. PLUGGING iN MOTOR 1. From among the loose parts find: 2 Wire Ties 2. Route Motor Cord along dghtside ofcabinet and snap ties in 1/4 inch bole in side of cabinet. Secure cord in wire ties, 3. Plug Motor cord into outlet on side of switch box. WIRE TIES EXTENSION REMOVED FOR PICTURE CLARITY 24 getting to know your saw 9 SAWBLADE S TABLE INSERT J 7 BLADE GUARD |0 EXACT-I-CUT ANTIKICKBACK PAWLS 6 MITER GAUGE RiP FENCE HOLES; ATTACHING FOR FACING RiP LOCK FENCE HANDLE 4 TILT LOCK HANDLE (UNDERNEATH TABLE) 2 ELEVATION HANDWHEEL 3 TiLT HANDWHEEL 1 ON-OFF SWITCH ON-OFF SWITCH CAUTION: Before turning switch "ON", make sure the blade guard Is correctly Installed and operaUng properly. The On-Off Switch has a locking feature. THIS FEATURE IS INTENDED TO PREVENT UNAUTHORIZEDAND POSSIBLE HAZARDOUS USE BY CHILDREN AND OTHERS. A. To turn saw ON, stand to either sideot the blade, never in line with it, insert finger under switch lever and pull END of lever out. KEY (YELLOW PLASTIC) Afterturning switchON, always allow the blade to come up to full speed before cutting. Do notcycle the Motor Switch on and oft rapidly, as this may cause the sawblade to loosen. Inthe event this should ever occur, allow the sawblade to come to a complete stop and retighten the arbor nutnormally, not excessively. Never leave the saw while the power in =ON", B. Totum saw OFF, PUSH leverin. Never leave the saw untilthe cutting tool has come to a complete stop. C. To lockswitchinOFF position, hold switch IN with one hand, REMOVE key with other hand. WARNING: For your own safety, lower blade or other cutting tool below table surface. (If blade Is Ulted. return It to vertical, 90°, position). Always lock the switch "OFF". When saw Is not in use, remove key and keep it in a safe place. Also, in the event of a power failure (all ofyour,ghts go out) turn switch off, lock It and remove the key. This will prevent the saw from starting up again when the power comes back on, 25 getting to know your saw 2 ELEVATION HANDWHEEL ... elevates or Iowersthe blade, Turnclockwiseto elevate, counterclockwise to lower. 3 TILT HANDWHEEL...tilts the blade for bevel cutting. Turn clockwise to tilt toward left,counterclockwise to tilt toward dght. When the blade is tilted to the LEFT as far as itwill go, it should be at 45" to the table and the bevel pointer should point 45°. NOTE: There are LIMIT STOPS inside the saw which prevent the blade from tilting beyond 45° to the LEFT and 90° to the RIGHT. ( See "ADJUST MENT,<;AND ALIGNMENTS"section"BLADE TILT, OR SQUARENESS OF BLADE TO TABLE"). 4 TILT LOCK HANDLE... locks the blade inthe desired tilt position. To loosen, turn counterclockwise. Push handle in and turn it to another position if necessary in order to tighten or loosen. 5 RIP FENCE... islocked inplace by pushingthe LockLeverdownuntilthe leverrests onthe stop. To move the Fence, lift the Lock Lever and grasp the Fence with one hand at the front. Holes are provided inthe Rip Fence for attaching a wood facing when using the Dado Head, or Molding Head. Select a piece of smooth straight wood approximately 3/4 inch thick, and the same size as the Rip Fence. Attach it to the Fence with three Round Head #10 Wood Screws, 2 inches long. TO removethe facing, loosen the screws, slide the facing forward and pull the screws through the round holes. WOOD FACING t 6 MITER GAUGE .., headislockedin positionfor crosscuttingorrnitedngbytighteningthe LockKnob. ALWAYS LOCK IT SECURELY WHEN IN USE. Gauge to cut miters. NOTE: The slotsfor the Stop Pin and the graduations are manufactured to very close tolerances which provide accuracy for average woodworking. In some cases where extreme accuracy is required, when making angle cuts. forexample, make a trial cut and then recheck it. If necessary, the Miter Gauge head can then be swiveled slightlyto compensate and then locked. Slots are provided in the Miter Gauge for attaching an Auxiliary Facing to make it easier to cut long pieces. Be positive Facing does not interfere with the proper operation of the Sawblade Guard. Select a suitable piece of smooth straight wood, ddll two holes through it and attach it with screws. NOTE: When bevel crosscutting, attach Facing so that it extendsto the dght of the Miter Gauge and use the Miter Gauge in the groove to the righl of the blade. FACING STb.PI. +s+soT \ I IFO. STO..,. 7 BLADEGUARD...must always be in place and work...
Ce manuel est également adapté pour les modèles :Jig Saw et - 113.298721, 113.298761 (4.78 mb)