Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. 6. Do not freeze or immerse charger in water or any other liquid. : Shock hazard. Do not allow any liquid to get inside charger. : Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling. INSTALLING AND REMOVING THE BATTERY PACK FROM THE TOOL : Make certain the lock-off button is engaged to prevent switch actuation before removing or installing battery. TO INSTALL BATTERY PACK: Insert battery pack into tool as shown in figure C. C 9 90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 10 TO REMOVE BATTERY PACK: Depress the battery release button as shown in figure D and pull battery pack out of tool. D SAVE THESE INSTRUCTIONS OPERATION : Before attempting any of the following operations, make sure that the saw blade has stopped, and the battery is removed. Used saw blades can be hot. Blade Installation (FIGURE E) -Hold the saw blade with teeth facing forward. -Holding the saw upside down, push the saw blade locking lever (3) downward. -Insert the shank of the saw blade into the blade holder as far as it will go. - Release the lever. -Check to ensure blade is secure before cutting. E ADJUSTING THE SHOE PLATE FOR BEVEL CUTS (FIGURE F) : Never use the tool when the shoe plate (5) is loose or removed. The shoe plate can be set to a left or right bevel angle of up to 45°. -Turn the locking knob (6) in direction A to release the shoe plate (5). -Pull the shoe plate (5) backwards and set it to the required angle. You can use the scale or a protractor to check the angle. -Turn the locking knob (6) in direction B to lock the shoe plate in place. To reset the shoe plate for straight cuts: F -Turn the locking knob (6) in direction A to release the shoe plate (5). -Pull the shoe plate backwards and set it to an angle of approximately 0. -Push the shoe plate forward. -Turn the locking knob (6) in direction B to lock the shoe plate in place. Make sure that the shoe plate is supported by the guide ribs. 10 90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 11 SWITCHING ON AND OFF -To switch the tool on, depress the lock-off button (2) then press the variable speed switch (1). The tool speed depends on how far you depress the switch. -To switch the tool off, release the variable speed switch. ORBITAL ACTION SELECTOR (FIGURE G) -For fast, rough straight cuts in wood, set the orbital action selector (7) to the symbol (II). -For fast, smooth straight cuts in wood, set the orbital action selector (7) to the symbol (I). -For accurate, straight and curve cutting and a smooth surface finish, set the orbital action selector (7) to the symbol (0). -NOTE: Orbital action is not recommended when curve cutting or for use in metals. G CONNECTING A VACUUM CLEANER TO THE TOOL (FIGURE H) -Align the dust extraction adaptor (8) with the saw shoe as shown. -Insert the ribs (9) into the slots (10). -Rotate the adaptor until it locks into position. Make sure that the ribs (9) are correctly seated. -Connect the vacuum cleaner hose (not supplied) to the adaptor. Dust extraction is not possible when making bevel cuts. Hints for optimum use H POCKET CUTTING A pocket cut is an easy method of making an inside cut. The saw can be inserted directly into a panel or board without first drilling a lead or pilot hole. In pocket cutting, measure the surface to be cut and mark clearly with a pencil. Next tip the saw forward until the front end of the shoe sits firmly on the work surface and the blade clears the work through its full stroke. Switch the tool on and allow it to attain maximum speed. Grip the saw firmly and lower the back edge of tool slowly until the blade reaches its complete depth. Hold the shoe flat against the wood and begin cutting. Do not remove blade from cut while it is still moving. Blade must come to a complete stop. FLUSH CUTTING A flush cut is necessary when finishing off cuts up to a wall or an obstacle, such as back- splash. One of the easiest ways to accomplish the flush cut is to use a flush cutting blade. The flush cutting blade provides the reach necessary to cut right up to the front edge of the jig saw shoe. Return the shoe to the 0° positive stop position before installing and using the flush cutting blade. For the best cut quality the flush cutting blade should be used in the 0 or I orbital position. The flush cutting blade should not be used to start the cut because the flush cutting blade prevents the shoe from being supported by the work surface. Use wood cutting practices explained below. WOOD CUTTING Support the workpiece adequately at all times. Use a higher speed for cutting wood. Do not attempt to turn the tool on whe...
Ce manuel est également adapté pour les modèles :Jig Saw et - 90550119 (907.92 kb)