Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
Standards by Underwriters Laboratories. -5 This symbol designates that this tool complies to NOM Mexican Standards. Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. -6- Functional Description and Specifications ! WARNING Model number 1640VS Voltage rating 120 V 50 - 60Hz Amperage rating 3.5 A No load speed n0 2,000-2,800/min Maximum capacities Stroke length 5/8" Wood 2-1/2" Plastic 3/4" Finecut™ Power Handsaw SAW BLADE GUIDE SAW BLADE DRIVE PIN SLIDE ON/OFF SWITCH VARIABLE SPEED DIAL VENTILATION OPENINGS VENTILATION OPENINGS CLIC BUTTON FLUSH-CUT BLADE SAW TEETH PROTECTOR LOCKING SPRING SAW BLADE DRIVE PIN HOOK Do not use this tool to cut drywall or plaster walls. This tool and its blades are designed to cut wood and plastic products. Fine drywall or plaster dust will cause the reciprocating mechanism to jam. ! CAUTION FIG. 1 TAB -7- Functional Description and Specifications (cont.) THUMB SCREW GUIDE PINS PRESET ANGLE RELEASE BUTTON BLADE ALIGNMENT SCREW SAW TEETH PROTECTOR DUST PORT ANGLE INDICATOR LOCKING SCREW TURNTABLE WITH PIVOTING SAW HOLDER WORKPIECE FENCE THUMB SCREW GENERAL PURPOSE BLADE MOUNTING SCREW HOLE MOUNTING SCREW HOLE MITER TABLE ATTACHMENT TABLE CLAMP (2) THUMBSCREW STORAGE STOP FIG. 2 Finecut™ Power Handsaw with Optional Miter Table Attachment WORKCLAMP (1) -8- Assembly INSERTING AND CHANGING THE BLADE The machine is equipped with a Bosch "Clic" blade-clamping device. This feature makes changing blades simple and fast without additional tools. FLUSH-CUT SAW BLADE This blade’s teeth are offset from the blade guide, which facilitates flush cutting. The flush-cut saw blade can be attached to the tool depending on desired sawing direction, or personal preference (Fig. 3). Hook the respective small tab for sawing direction (A) or (B) completely onto hook as shown in figures 4 or 5 depending on personal preference. Then swing the saw blade in the direction of the arrow and press the large tab onto the locking spring until it latches. If necessary, wipe the blade clean. Only then should the saw teeth protector be removed. Insert plug into power source and turn tool on briefly (See Operating Instructions for Saw Section). This will allow the saw blade pin to engage into the blade to drive the blade back and forth. Turn tool off. To change the blade, place the saw teeth protector onto the blade and press the “Clic” button. This causes the tab to spring out of the locking spring, then remove the blade. GENERAL PURPOSE SAW BLADE The general purpose saw blade can also be attached depending on desired sawing direction or personal preference (Fig. 6). Hook the respective small tab for sawing direction (C) or (D) completely onto hook as shown in figures 7 or 8 depending on personal preference. Then swing the saw blade in the direction of the arrow and press the large tab onto the locking spring until it latches. FIG. 4 FIG. 5 FIG. 6 FIG. 7 HOOK LOCKING SPRING DRIVE PIN LARGE TAB SMALL TAB DRIVE PIN LOCKING SPRING HOOK SMALL TAB LARGE TAB BLADE BLADE LOCKING SPRING DRIVE PIN SMALL TAB LARGE TAB “CLIC“ BUTTON II I FIG. 3 HOOK If necessary, wipe the blade clean. Only then should the saw teeth protector be removed. FIG. 8 Insert plug into power source and turn tool SMALL on briefly (See Operating Instructions TAB Section). This will allow the saw blade pin to engage into the blade, which drives the blade back and forth. Turn tool off. To change the blade, place the saw teeth protector onto the blade and press the “Clic “ button. This causes the tab to spring out of the locking spring, then remove the blade. LOCKING DRIVE PIN HOOK LARGE TAB SPRING Assembly of Miter Table Attachment MOUNTING MITER (Model 1640VSK only) MOUNTING MITER TABLE ATTACHMENT TABLE ATTACHMENT USING CLAMPS WITH SCREWS Remove the thumbscrew from the storage Your miter table attachment is equipped with area located on the underside of the miter two mounting holes that will allow you to table fixture (Fig. 2). more permanently mount the miter table attachment to a surface without the use of Place the stop on the table attachment the table clamps (Fig. 10). To attach, simply against the edge of the workbench or table, screw two screws of sufficient length (not and fasten the miter table attachment with provided) through the two holes provided in the aid of the two matching table clamps. To the miter table attachment and into the do this properly, slide the table clamps in mounting surface. completely in (Fig. 9). When repacking the case (included with model 1640VSK), place the table clamps below the miter table attachment. ATTACHING THE SAW Place the tool as shown in figure 2 on the pivoting saw holder of the turntable and secure with thumbscrew. Make sure that the guide pins located on the miter table attachment engage in the holes on the tool. FIG. 9 FIG. 10 STOP TABLE CLAMP TABLE CLAMP MOUNTING SCR...
Ce manuel est également adapté pour les modèles :Jig Saw et - 1640VS (2.57 mb)