Évaluations - 3, GPA: 5
(
)
)
|
Facilité d'utilisation
2 LOCK BUTTON -8 BM 2610917132 10-03 10/28/03 11:07 AM Page 9 Installing Power Corh !WARNING DIRECT CORD CONNECT ATTENTION: before inserting plug into SYSTEM HAS BEEN handle, always make sure you leave enough CONFIGURED TO BE USED WITH 12AWG cord at plug end to avoid tension on plug SJ CORD, MAXIMUM LENGTH OF 50 FEET. when inserted into tool. INSPECT THE CORD, DO NOT USE IF 3. Push end of plug through spring clip and DAMAGED. into female outlet in handle as shown below . 1. Loop cord as shown in figure A. 4 To remove plug from tool, simply remove 2. Insert looped end of cord through slot in from outlet and pull away from spring clip. handle and loop cord into channel provided NOTE: If the spring clip does not securely in handle as shown figure. B). hold the plug it may be necessary to lightly squeeze the clip together with a pliers. FIG. A FIG. B SPRING CLIPSPRING CLIP -9 BM 2610917132 10-03 10/28/03 11:07 AM Page 10 Operating Instructions FIG. 3 DEPTH ADJUSTMENT DEPTH ADJUSTMENT LEVER Disconnect plug from power source. Loosen the depth adjustment lever located between the guard and handle of saw. Hold the foot down with one hand and raise or lower saw by the handle. Tighten lever at the depth setting desired. Check desired depth (Fig. 3). Not more than one tooth length of the blade should extend below the material to be cut, for minimum splintering (Fig. 3). ONE TOOTH LENGTH SHOULD PENETRATE WOOD FOR MINIMUM SPLINTERING 90° CUTTING ANGLE CHECK Disconnect plug from power source. Set foot to maximum depth of cut setting. Loosen bevel adjustment lever, set to 0° on quadrant, retighten bevel adjustment lever first, then the depth adjustment lever and check for 90° angle between the blade and bottom plane of foot with a square (Fig. 4). Make adjustments by turning the small alignment screw from bottom side of foot, if necessary (Fig. 4). 90° QUADRANT FIG. 4 BEVEL ADJUSTMENT LEVER FOOT BLADE 0° ALIGNMENX SCRE[ BEVEL ADJUSTMENT Disconnect plug from power source. The foot can be adjusted up to 45° by loosening the bevel adjustment lever at the front of the saw and aligning foot to desired angle on calibrated quadrant. To maintain adjustment, Always tighten bevel adjustment first, then the depth adjustment lever (Fig. 5). For 50° cuts, loosen bevel adjustment lever, depress 45° stop spring, adjust foot to 50° and tighten lever (Fig. 5). Because of the increased amount of blade engagement in the work and decreased stability of the foot, blade binding may occur. Keep the saw steady and the foot firmly on the workpiece. QUADRANTBEVEL ADJUSTMENT LEVER FIG. 5 45° STOP SPRING LINE GUIDE FOOT 90° VERTICAL CUTS For a straight 90° cut, use the large notch in the foot. For 45° bevel cuts, use the small FIG. 6 45° / 50° BEVEL CUTS notch (Fig. 6). The cutting guide notch will give an approximate line of cut. Make sample PUSH cuts in scrap lumber to verify actual line of 45°STOP SPRING IN DIRECTION cut. This will be helpful because of the number of different blade types and OF ARROW thicknesses available. To ensure minimum FOR 50° splintering on the good side of the material to BEVEL be cut, face the good side down. ADJUSTMENT -10 BM 2610917132 10-03 10/28/03 11:07 AM Page 11 SWITCH When starting the tool, hold it with both hands. !WARNING The torque from the motor can cause the tool to twist. To turn tool “ON”, squeeze the trigger switch. To turn the tool “OFF”, release the trigger switch, which is spring loaded and will return to the off position automatically. Your saw should be running at full speed BEFORE starting the cut, and turned off only AFTER completing the cut. To increase switch life, do not turn switch on and off while cutting. GENERAL CUTS Always hold the saw handle with one hand and the auxiliary handle or housing with the other. !WARNING Always be sure either hand does not interfere with the free movement of the lower guard. Maintain a firm grip and operate the switch with a decisive action. Never force the saw. Use light and continuous pressure. !WARNING After completing a cut and the trigger has been released, be aware of the necessary time it takes for the blade to come to a complete stop during coast down. Do not allow the saw to brush against your leg or side, since the lower guard is retractable, it could catch on your clothing and expose the blade. Be aware of the necessary blade exposures that exist in both the upper and lower guard areas. When cutting is interrupted, to resume cutting: squeeze the trigger and allow the blade to reach full speed, re-enter the cut slowly and resume cutting. When cutting across the grain, the fibers of the wood have a tendency to tear and lift. Advancing the saw slowly minimizes this effect. For a finished cut, a cross cut blade or miter blade is recommended. CUTTING MASONRY/METAL This tool is not recommended for continuous and general usage with metal or masonry cutoff wheels. If you use your saw for cutting these materials, use the appropriate wheel for the material bei...
Ce manuel est également adapté pour les modèles :Jig Saw et - 1677MDT (800.66 kb)