Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
They must also wear respiratory protection if no dust removal system is used. Wear Wear Wear Wear eye ear protective breathing protection protection gloves protection 5.6 Protective devices Never operate the tool without the applicable protective devices (dust hood). en 17 6. Before use en -CAUTION . The cutting edges of the saw blade are sharp. . The cutting edges may present a risk of injury. . Wear protective gloves. 6.1 Extension cords If extension cords are used: Use only extension cords of a type approved for the intended purpose and of adequate cross section. Failure to observe this point may result in reduced performance and may cause the cord to overheat. Replace damaged extension cords. Use only correspondingly marked and approved extension cords for working outdoors. Recommended minimum cross sections and max. cord lengths: Mains voltage Conductor cross section 1.5 mm2 2.5 mm2 110 V 20 m 30 m 230 V 50 m 100 m Extension cords for outdoor use For outdoor work use only extension cords approved and correspondingly marked as suitable for outdoor use. 6.2 Fitting the saw blade 1. Unplug the supply cord from the electric socket. 2. Press the saw blade release lever and hold it in this position. 3. Push the saw blade into the blade holder (teeth facing cutting direction) until it engages. 4. Hold the blade against the resistance felt and then allow the blade release lever to return to its original position. 5. Check that the blade is held securely by gripping and pulling it. 6.3 Changing the saw blade -NOTE- When changing the saw blade, hold the tool in such a way that persons or animals cannot be injured by the saw blade as it is ejected. 1. Unplug the supply cord from the electric socket. 2. Press the saw blade release lever to the side as far as it will go. The saw blade is then released and ejected. 6.4 Dust removal using an external dust removal system -NOTE- Use of a dust removal system reduces exposure to dust, increases safety at the workplace by ensuring better vis ibility of the cutting line and helps to keep the workplace tidy by greatly reducing the amount of dust and wood chips in the working area. Connect the external dust removal system before working with the tool for long periods when cutting wood or other materials that may cause considerable dust. The dust removal hood must be fitted when the tool is being used with a dust removal system. 6.4.1 Connecting the system 1. Unplug the supply cord from the electric socket. 2. Fit the dust removal adaptor into the opening on the tool. 3. Push the dust removal adaptor toward the tool from below until it engages. 4. Connect the vacuum cleaner hose to the dust removal adaptor. 6.4.2 Disconnecting the system 1. Unplug the supply cord from the electric socket. 2. Disconnect the vacuum cleaner hose from the dust removal adaptor. 3. Push the dust removal adaptor downwards and pull it out of the tool. 6.5 Dust removal hood 6.5.1 Fitting the dust removal hood 1. Unplug the supply cord from the electric socket. 2. Push the dust removal hood onto the tool from the front until it engages. 6.5.2 Removing the dust removal hood 1. Unplug the supply cord from the electric socket. 2. Tilt the dust removal hood slightly and pull it away from the tool toward the front. 6.6 Sawdust blower The blower keeps the cutting line free of dust and chips by directing a jet of air toward the saw blade. 6.7 Adjusting the orbital action The four orbital action settings permit cutting performance and quality of cut to be adjusted to suit the material being cut. Orbital action adjustment lever is used to set the tool to one of the four orbital action settings. Please observe the following recommendations: The lower the orbital action setting, the finer and cleaner the cut. The optimum setting can be determined by making test cuts. Setting 0: No orbital action Setting I: Low orbital action Setting II: Medium orbital action SettingIII: High orbital action 18 Please refer to the information provided with the saw blade for details of correct settings. 6.8 Adjusting the stroke rate 1. Set the stroke rate adjustment thumbwheel to a position between 1 (slow) and 6 (fast). Please refer to the information provided with the saw blade for details of correct settings. 6.9 Adjusting the cutting angle 6.9.1 Setting the cutting angle 1. Unplug the supply cord from the electric socket. 2. Remove the dust removal system adaptor. 3. Release the screw. 4. Pull the baseplate slightly toward the front of the tool. 5. Set the baseplate to the desired angle according to the scale on the tool. 6. Tighten the screw. 6.9.2 Resetting the cutting angle 1. Unplug the supply cord from the electric socket. 2. Release the screw. 3. Return the baseplate to the 0° position. 4. Push the baseplate back to its original position (toward the rear of the tool). 5. Tighten the screw. -CAUTION . The cutting edges of the saw blade are sharp. . The cutting edges may present a risk of injury. . Wear protective glo...
Ce manuel est également adapté pour les modèles :Jig Saw et - WSJ 750 (496.59 kb)