|
Facilité d'utilisation
1001 % a r jmSmSBmSSSmm •tv’*,.' vi/.’. ' ■- i 1 8k * V. 04/92 - EB-D - GB Stock-no. 115 107 8059 Contents 1.0 Scope of Application 2.0 Specifications 3.0 User Responsibility 4.0 Standard Accessories 5.0 Optional Accessories 6.0 Assembly 7.0 Mitre Fence Assembly 8.0 Installation 9.0 Operation/Settings 10.0 Cutting 11.0 Saw Dust Collection (optional accessory) 12.0 Crane Lifting 13.0 Safety Rules 14.0 Care and Maintenance 15.0 Wiring Diagrams 16.0 Spare Parts List and Drawing 1.0 Scope of Application - This site saw model BKS 400/BKS 450 has been designed to perform rip and cross cuts in wood having a square or rectangular cross section. - Cross cuts should only be performed with the help of the mitre fence. - Round stock or firewood should not be cut without an appropiate jig holding the work safely. - The maximum/minimum blade diameters are 400/350 mm for model BKS 400 and 450/350 mm for model BKS 450. 2.0 Specifications BKS 400/3.1 WNB BKS400/4.2 DNB BKS450/4.75DNB Table size 1000 x 665 mm 1000 x 665 mm 1000 x 665 mm Table height from floor 850 mm 850 mm 850 mm Depth of cut 127 mm 127 mm 152 mm Motor speed 50/60 Hz 2800/3360 rpm 2800/3360 rpm 2800/3360 rpm Cutting speed 58.5 m/sec 58.5 m/sec 66 m/sec Motor capacity P1 S6 40% 3.1 kW 4.2 kW 4,75 kW Motor capacity P2 S1 100% 1.5 kW 2.1 kW 2.4 kW Voltage 1 ~ 220/240V 3~ 380/440V 3~ 380/440V Mains fuse 1 x 16A 3 x 16A 3 x 16A Max. saw blade diameter 400 mm 400 mm 450 mm Min. saw blade diameter 350 mm 350 mm 350 mm Saw blade bore 30 mm dia. 30 mm dia. 30 mm dia. Note: Saw blade 450mm diameter requires 4.75kW motor. Use of 450mm blades with 3.1 kW and 4.2kW motor voids factory warranty! 3.0 User Responsibility This machine will perform in conformity with the description contained in the instructions provided. This machine must be checked periodically. Defective equipment (including service leads) should not be used. Parts that are broken, missing, plainly worn, distorted or contaminated, should be replaced immediately. Should such repair or replacement become necessary, it is recommended that such repairs are carried out by qualified persons approved by the equipment manufacturer or its representative. This machine or any of its parts should not be altered or changed from standard specifications. The user of this machine shall have the sole responsibility for any malfunction which results from improper repair by anyone other than qualified persons approved by the equipment manufacturer or its representatives. Note Within the U.K., this machine falls under the Woodworking Machinery Regulations 1974, under which certain operations, e.g. grooving, rebatting, tenoning and moulding are prohibited without special guards. For your own safety it is recommended to follow the instructions given in the Health and Safety at Work booklet No.41, entitled “Safety in the Use of Woodworking Machines” and “A Guide to Woodworking Machinery Regulations” HS(R)9. Both publications are available from Her Majesty’s Stationary Office and other bookshops. The information contained in this manual is intended to make the operator of this saw familiar with its safety features, setting of guards and fences, and the safe performance of the different basic cutting operations normally carried out with this type of saw. It does not teach the operator how to become an expert woodworker. Those persons interesting in gaining a more intimate knowledge on the tasks which can be carried out on this type of saw are advised to refer to commercially available literature on the subject. 4.0 Standard Accessories - Saw blade - Riving knife DIN 38820 Gr. 50x3 - Saw blade guard - Rip fence - Mitre fence - Lifting eyes - Push stick - Tool set - Operating instructions 5.0 Optional Accessories For the ELEKTRA Site Saws BKS the following accessories are available at extra cost: - Sliding Carriage BKS/BKH Stock-no. 0910 00666 5 - Extension Table BKS/BKH Stock-no. 0910 00667 3 - Dust Extraction Adaptor BKS 100mm Stock-no. 0910 00874 9 - Log Cutting Attachment BKS/BKH Stock-no. 0910 00886 2 6.0 Assembly Place table onto firm support (e.g. saw horses). Attach table insert (aluminium extrusion) to table; use 10 pcs. countersunk flat-head screw 4.2x13. Bolt rip fence guide extrusion to front of table. Bolt both support brackets to the motor. Use 4 each hex. head screw M8x16 hex. nut M8. Attach the thus preassembled motor to the table, but do not yet tighten fully. Use 4 each countersunk screw M8x16 hex.nut M8 washer 8.4 Install saw blade onto motor, than align motor so that the saw blade is centered in the table insert’s slot. When positioned correctly fully tighten the motor on the table. Attach mounting plate for the riving knife carrier bracket to the table. Use 4 each countersunk screw M6x16 hex. nut M6 Attach riving knife carrier bracket loosely to mounting plate. Use 4 each hex. head screw M6x16 washer 6.4 hex. nut M6 Place carriage...
Ce manuel est également adapté pour les modèles :Jig Saw et - BKS 400 (4.05 mb)