Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Manual de instrucciones Pagina 10- 13 IMPORTANTE: Lea y comprende todas las instrucciones antes de usar. KA-KS 120 475825_001 Trimming attachment KA-KS 120 right 2 x KA-KS 120 Scope of delivery The trimming attachment consists of the following main components: (1.1) Stop profile left (1.2) Tape measure clamp (1.3) Support (1.4) Support plate (1.5) Stop flag (1.6) Adjustable spacer (1.7) Extendable end piece (1.8) Leg support plate (1.9) Tape measure (1.13) Cross brace 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1 1.12 1.131.111.10 2.1 Preparations –Secure the KS 120 to a Festool multifunction table (MFT) or a work bench with a height of 31.1 in./790 mm (see operating manual KS 120). 2.2 Leg support plate The leg support plate (1.8) is designed to support the trimming attachment and is fixed to the extendable end piece (1.7). 3.6 3.7 3.5 3.4 3.3 3.2 3 3.1 3.8 2 Set-up When setting up the attachment, proceed in the sequence specified. Important: you will require a crown moulding stop (AB-KS 120) to make the connection to the KS 120. Refer to Figure 1 for the arrangement and positioning of the individual parts. Fig. 1 shows a rear view of the trimming attachment. The following section describes how to attach the right trimming attachment. Use the same procedure to attach the left trimming attachment! Fig. 2 shows the stop mounted on both sides! –Unscrew both rotary knobs (3.1) until the two support legs (3.3) can be inserted into the clamping sleeves (3.4). –Insert the support legs until the leg support plate reaches the same height as your KS 120. –Tighten the rotary knobs (3.1) to clamp the support legs in place. –Screw the rotary knob (3.2) through the recess (3.5) and into the slot nut (3.8) in the bottom slot (3.7) on the extendable 2 3 end piece to secure the mounting plate. Note: The two cams (3.6) must slot into the groove (3.7). 3.2 Cross brace Secure the cross member (1.13) to the stop profi le. – Slide the slot nut (4.2) into the stop profi le (4.1). 4 4.1 4.2 4.4 4.3 2.4 Stop profi le Secure the stop profi le to the bench for the bracket support (AB-KS 120): 5 5.5 5.4 5.3 5.1 5.2 – Insert the rotary knob (5.4) through the hole (5.5) in the bracket support bench and secure the slot nut (5.2). Do not tighten the knob yet – you must be able to lift the slot nut approx. 0.2 in. above the bracket support. – Slide the stop profi le (5.1) onto the slot nut (5.2) until the stop profi le is fl ush with the edge of the bench (5.3). – Fit the bracket support bench to the KS 120 (see bracket support assembly instructions). – Align the bracket support bench so that the stop profi le is fl ush with the stop ruler on the KS 120. Clamp the bracket support bench in place (see bracket support assembly instructions). – Insert a clamp (6.3) in the hole (6.1) to secure the cross brace (6.2) to the MFT. Do not tighten yet! 6.1 6.2 6.3 6 –Use a long workpiece to align the trimming attachment in relation to the compound mitre saw. – Tighten the rotary knob (5.4). – Now tighten the connections on the cross braces (4.4) and (6.3). 2.5 Tape measure, tape measure clamp 7.1 7.2 7.3 7.4 7 – Insert the tape measure (7.1) into the extendable end piece. – Guide the tape measure (7.2) through the top grooves on the extendable end piece, the adjustable spacer and the stop profi le in succession. – Unscrew the rotary knob (7.4) for the tape measure clamp. – Insert the slot nut for the tape measure clamp into the slot (7.3) on the stop profi le. –Secure the tape measure clamp towards the end of the tape measure by tightening the rotary knob (7.4). 2.6 Support plate The support plate (1.4) is used to support longer workpieces. 8 8.38.1 8.2 8.5 8.4 –Screw the rotary knob (8.5) through the recess (8.4) and into the slot nut (8.1) in the slot (8.2) on the stop profile to secure the support plate. Note: The two cams (8.3) must slot into the groove (8.2). –If necessary, extend the telescopic section of the trimming attachment 4 in. to insert the support plate into the groove. 2.7 Support The support (1.3) is used to support taller workpieces. 9 9.1 9.2 9.3 –Unscrew the rotary knob (9.1) that clamps the support. –Insert the slot nut (9.3) into the top slot (9.2) on the stop profile or the adjustable spacer. –If necessary, extend the telescopic section of the trimming attachment 4 in. to insert the support plate into the groove. –Slide the support to the required position. –Tighten the rotary knob (9.1) to secure the support. 2.8 Stop flag The stop flag (1.5) is used to adjust the distance between the saw blade and the workpiece so that the workpiece is cut to the required length. –Unscrew the rotary knob (1.11) on the adjustable spacer. –Move the stop profile (1.1) and the spacer (1.6) approx. 3.1 in. apart. 10 10.1 10.2 10.310.4 –Unscrew the rotary knob (10.1) that clamps the stop flag. –Insert the slot nut (10.3) into the top slot (10.2) on the stop profile or the adjustable spacer. –Slide the stop flag to the required position. –Tighten the rotar...