Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
Manual de instrucciones Pagina 22 - 31 IMPORTANTE: Lea y comprende todas las instrucciones antes de usar. Instruction manual Guide d’utilisation Manual de instrucciones MFT/3 MFT/KAPEX 475235_003 2 Table of Contents Health hazard by dust Technical data 3 Symbols 4 Design 4 Intended use 4 MFT/3: Setting up and assembly 5 Step 1: Setting up 5 Step 2: Trim splinter guard 5 Step 3: Setting up the guide rail support 6 Step 4: Attaching the guide rail 7 Step 5: Attaching the pre-set profi le setting rail 7 Step 6: Calibrating angle 8 Step 7: Adjusting the pre-set profi le set ting rail 8 Step 8: Adjusting the guide rail in rela tion to the workpiece 9 Step 9: Adjusting the cutting depth for sawing [Fig. 11] 9 MFT/KAPEX: Mounting the KAPEX 10 Maintenance 10 Turning the perforated top 10 Accessories, tools 10 Warranty 11 Various dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints, • Crystalline silica from bricks and cement and other masonry products, •Arsenic and chromium from chemically- treated lumber. The risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals work in a well ventilated area and use approved safety equipment, such as dust masks that are specially designed to fi lter out microscopic particles. TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND INSTRUCTION MANUAL. ..The multifunction table offers a wide range of application options! To find out more about possible machine applications, order the MFT application manual on the internet. Technical data MFT/KAPEX MFT/3 Bench dimensions (width x length) 1157 x 773 mm Bench height - with foldaway legs 900 mm - without foldaway legs 180 mm max. working width 700 mm max. workpiece thickness 78 mm Weight 28 kg Bench dimensions (width x length) 869 x 581 mm Bench height - with foldaway legs 790 mm - without foldaway legs 180 mm Weight 18 kg 4 Intended use The multifunction table MFT/3 is designed for safe, accurate sawing and routing in combination with Festool electric power tools. The clamping systems included in the accessories programme enable the user to attach workpieces securely to the worktop. The base becomes a work bench for various tasks such as planing, sanding, carving, etc. The multifunction table MFT/KAPEX was specially designed for attaching the KAPEX KS 120. The user bears the responsibility for damage and accidents caused by improper use. 1-3 1-4 1-8 1-7 1-1 1-2 1-3 1-5 1-6 1-9 1-10 Symbols Warning of general danger Read the Operating Instructions/ Notes! Design MFT/3 and MFT/KAPEX [1-1] Bench consisting of: profi le frame, corner feet, perforated top, foldaway legs MFT/3 only [1-2] Support unit [1-3] Guide rail FS 1080 [1-4] Swivel unit [1-5] Pre-set profi le setting rail and [1-6] Stop ruler [1-7] Additional clamp for stop ruler [1-8] Stop fl ag MFT/3-AR [1-9] Defl ector 1 5 MFT/3: Setting up and assembly Accessory attachments can be secured at different points on the multifunction table to enable different working positions. In the standard working position, the user stands along one side of the bench [Fig. 2]. In these operating instructions, this side of the bench is referred to as the "front". Step 1: Setting up Take the table out of the box. Screw on the knobs [2-3] until the stop is reached. Unfold the foldaway legs and tighten the knobs on the joints to secure. Turn the end cap [2-1] on the right to adjust the length of the leg and compensate for an uneven fl oor surface. NOTE: The corner feet [2-2] are fi tted with rubber caps so that the bench stands securely when the legs are folded away. Step 2: Trim splinter guard Now you are ready to set up the guide rail system. The fi rst thing to do is to trim the splinter guard [3-4] of the guide rail using your Festool plunge-cut saw. Place your saw on top of the guide rail and tune it to the track on the rail using a screwdriver [3-3] to loosen or tighten the front and back set screws so that there is no play between the sole plate of the saw and he raised portion of the guide rail. However, make sure that the saw still glides smoothly on top of the guide rail. 3-1 3-2 3 3-3 3-4 2-1 2-2 2-3 2 6 Adjust the speed of the saw [3-2] to a setting of „6“ (maximum speed). Set the depth of cut, using the depth stop adjustment [3-1], to 8 mm (5 mm for the thickness of the guide rail plus 3 mm cutting depth) and cut the splinter guard along the full length without interruption. For trimming the splinter guard it is best to use some sort of backing piece, such as plywood or fi berboard. The edge of the splinter guard now corresponds exactly to the cutting edge. Step 3: Setting up the guide rail support The table comes from the factory with two stops [4-2, 4-4] pre-set on the long sides of the profi le f...
Ce manuel est également adapté pour les modèles :Jig Saw et - MFT/3 (2.41 mb)