-36 Figure 45. Crosscutting blade. Combination Blade: Used for cutting with and across the grain. A compromise between a rip blade and a cross-cut blade, a 10" combination blade will typically have between 40-50 teeth (Figure 46), an alternate top bevel and flat or alternate top bevel (Figure 49) and raker tooth profile. The teeth are arranged in groups of five. The gullets are small and shallow within the groups of five teeth, similar to a cross-cut blade; then large and deep between the groups

#TS10279 PRINTED IN TAIWAN .........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

2. Rotate both knurled stripper adjustment shafts together (see Figure 17) to raise the hold-down slightly higher than the thickness of the workpiece. Stripper Adjustment Shafts Table Guides Figure 17.Typical punch station setup with a workpiece mounted on the table. -21 G0646/G0647 50/65 Ton Ironworker 3. Brush one of the lubricants from Figure 18 or an equivalent onto the punch, die, and both sides of the workpiece. Brand Type B.P. Servora 68 Castrol Ilobroach 219 Duckhams Adfornal EP7 Shell G

Flashing GREEN Constant Beeping (every 1/2 second) Low Battery Warning - The Back-UPS is supplying battery power to the load connected to the battery outlets, and the battery has 1.5 minutes of battery power remaining. Alternating GREEN & RED Constant tone Bad Battery Detected - Battery needs to be charged, or is at end of life and must be replaced (see Replace Battery). FlashingRED Constant tone Battery Disconnected - The battery is disconnected or it is a bad battery (see Replace Battery). Off

Off Short beep every 4 seconds Low Battery Shutdown - During On Battery operation the battery power was almost completely exhausted, and the Back-UPS is waiting for utility power to return to normal. Off Constant Tone On Battery Overload - Connected equipment requires more powerthan provided by Back-UPS battery. Unplug devices one at a time to remove overload. If not corrected contact APC Technical Support. GREEN On Constant Tone On Line Overload - The power drawn by the connected equipment exce

Place the dust port in the opening at the base of the saw. 2. Using a Phillips head screwdriver and an 8mm wrench, secure the dust port to the saw with the Phillips head screws, the hex nuts, the exterior tooth washers, and the toggle tabs (Figure 16). Figure 16. Dust port installation. Components and Hardware Needed: Qty Handwheels........................................................2 Threaded Chrome Handles 3.8"-16 x 1.2" ............2 Star Knobs 3.8"-16 ....................................

Place the table insert into the table. 2. Place a straightedge across the table and the table insert. 3. Using a 3mm Allen wrench, adjust the table insert flush with the table by rotating the setscrews as shown in Figure 36. Figure 36. Adjusting the table insert. G0444/G0444Z 10" Table Saw -27 G0444Z Power Cord The Model G0444Z ia prewired to operate on a G0444 The Model G0444 ia prewired to operate on a 110V power source. Connect the power cord to the motor according to Figure 37. ! Disconnect

G0451 14" Sliding Table Saw -9 Additional Safety Instructions for Table Saws 1. SAFETY ACCESSORIES. Always use the blade guard and riving knife on all ''throughsawing'' operations. Through-sawing operations are those when the blade cuts com7. RIVING KNIFE ALIGNMENT. Only operate the saw if the riving knife is aligned with the main blade. pletely through the workpiece. 8. REACHING OVER SAW BLADE. Never reach behind or over the blade with either 2. 3. KICKBACK. Be familiar with kickback. Kickback

16. re-install the table pin and table insert. 17. Fasten the rear rail to the back of the table with the four M6-1 x 16 cap screws, as shown in figure 15. figure 15. rear rail installed. 18. Attach the front rail to the front of the bandsaw table with the two M6-1 x 20 hex bolts, 6mm lock washers and flat washers, as shown in figure 16. 19. install the handle on the fence assembly (figure 17), and tighten the hex nut against the fence pivot block to secure the handle. pivot Block hex nut figure

Note: Get assistance positioning the tables and holding them in place while installing. Set Screws Mounting Screws Figure 20. Small extension wing attached. 4. Attach the support leg (Figure 21) to the large extension wing with the M10-1.5 x 45 hex bolt, lock washer, and flat washer. Figure 21. Support leg installed. 5. Check the table surfaces with a straightedge, as shown in Figure 22, to ensure that they are flush and even with each other. Figure 22. Checking with a straightedge. 6. Adjust th