It runs through normal 120-V alternating current power. When on, the saw blade has a stroke of 19/16 inches moving at a maximum speed of 2800 strokes per minute. The entire assembly, including the removable blade, weights 6.3 pounds. The saw has 6 speed settings, a trigger which determines whether the saw is on or off, and interchangeable blades. After completing the model and assembling it, we will attempt to animate several aspects of the construction and functions of the saw. Finally, we will

Make sure saw blade is clear of any foreign material and that power cord and extension cord are out of the blade path. Be sure material to be cut is held firmly. Small work pieces should be securely clamped in a vise or with clamps to the work bench or table. Mark the line of cut clearly. Depress the trigger switch starting the cutting action, set the base assembly against the work, then move the blade into the work. DO NOT FORCE. Use only enough pressure to keep the saw cutting. Let the blade a

Failure to do so could result in possible serious personal injury. BLADE WRENCH HOLDER A blade wrench (5 mm hex key) is packed with your saw. A convenient feature on your saw is the wrench holder. This is a slot located on the bottom portion of the saw handle. It is convenient for storing the wrench when it is not being used. BLADE SELECTION Your saw is equipped with a "lock-off" button which reduces the possibility of accidental starting. The lock-off button is located on the handle above the s

VARIABLE SPEED See Figure 2. Your reciprocating saw has a variable speed control selector designed to allow operator control and adjustment of speed and power limits. The speed and power of your saw can be increased or decreased by rotating the variable speed control selector in the direction of the arrows shown in figure 2. NOTE: Hold your saw in normal operating position and turn the variable speed control selector clockwise to increase the speed and power of your saw. Turn counterclockwise to

A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately. n Batteries vent hydrogen gas and can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately. n Do not charge battery tool in a damp or wetlocation. Following this rule will r

or 1-800-265-6778 in Canada SAVE THIS MANUAL FOR FUTURE REFERENCE SPECIFICATIONS: Length of stroke 1 in. (25.4mm) Strokes per minute 0-2000 spm Length (without blade) 17 in. (430 mm) Engine Type Air Cooled 2 Cycle Gasoline Engine Displacement 15.9 cc Starting System Recoil Carburetor Diaphram Fuel Tank Capacity 0.35 literes Net weight 11 lbs. STOP TABLE OF CONTENTS TABLE OF CONTENTS ¦ Table of Contents ..............................................................................................

n Green LED on = Fully charged and in maintenance charge mode. n Green LED on = When battery pack is inserted intocharger, indicates hot battery pack or that battery pack is out of or below normal temperature range. n Yellow and Green LEDs on = Deeply discharged ordefective battery pack. n No LED on = Defective charger or battery pack. CHARGING THE BATTERY PACK Battery packs for this tool have been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it un

WARNING: Do not allow familiarity with your circular saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. OPERATION OPERATION LED FUNCTION OF CHARGER 1400667 See Figure 2. LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK: ¦ Red LED Lighted = Fast Charging Mode. ¦ Green LED Lighted = Slow Charging Mode and Fully Charged Battery Pack. ¦ Yellow and Green LED Lighted = Soft Start Mode, or After 1/2 Hour Equals Hot or Defect

ASSEMBLY UNPACKING This product has been shipped completely assembled. nCarefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. nInspect the tool carefully to make sure no breakage or damage occurred during shipping. nDo not discard the packing material until you have carefully inspected and satisfactorily operated the tool. nIf any parts are damaged or missing, please call1-800-525-2579 for assistance. PACKING LIST Reciprocat

All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. WARNING: The double insulated system is intended to protect the user from shock resulting from a break in the tool's internal wiring. Observe all normal safety pre- cautions to avoid electrical shock. Important: Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qual