Évaluations - 3, GPA: 3.7 ( )

Fabricant : Kenwood Taille : 8.44 mb Nom Fichier : Langue d'enseignement:

Squelch will open only if the DTSS signal matches when scan stops. 4-5-3. Band Scan 1. Adjust the SQL control to the threshold point. 2. When one of the PRG-1, the PRG-2, or the MEMO indicator has been lit, press the SCAN key in the VFO mode. The MHz indicator begins flashing to indicate that the radio is scanning. 3. Scan will begin in an upwards direction. You can reverse the direction of scan by turning the Tuning control .The tuning step size depends on the current Frequency Step selection. 4. Scan stops on a busy channel, i.e. a station strong enough to open squelch and turn on the BUSY indicator. 5. Press the PTT switch or SCAN key to stop scan. 24 4-5-4. Programmable Band Scan • The Lower and the Upper Scan Limits Entry Select a frequency to be the lower or the upper scan limit. Press the M key for longer than 1 second, and then press the below key. Limit Programmable band scan 1 Programmable band scan 2 Upper 4/PROG-1 key 5 /PROG-2 key Lower 7/SEEK key 8 /CAR key • Confirmation of the lower and upper frequency limits Hold the F key down for longer than 1 second, then press one of the keys listed above. The upper or lower frequency limits will be displayed as VFO frequency. NOTES 1. If the step size of the lower limit frequency is different from that of the upper limit frequency, Programmable band scan will not start. 2. If the lower limit frequency is equal to or higher than the upper limit frequency, Programmable band scan will not start. • Selecting programmable band scan 1 or 2 When you press the F key, then the 4/PROG-1 key, the PROG1 indicator lights and programmable band scan 1 is selected. When you press the F key, then the 5/PROG-2 key, the PROG2 indicator lights and programmable band scan 2 is selected. • Programmable Band Scan 1. Adjust the SQL control to the threshold point. 2. Press the SCAN key. The PROG1/PROG2 indicator will begin flashing as a visual reminder the transceiver is scanning. Continue to 4-5-3 step 3. 4-5-5. MHz Scan 1. Adjust the SQL control to the threshold point. 2. Press the MHz key during band scan or programmable band scan. The MHz indicator will begin flashing as a visual reminder the transceiver is scanning. 3. Scanning will start in an upwards direction over a 1 MHz range. You can change the direction of scan by turning the Tuning control. Continue to 4-5-3 step 4. 4-5-6. Memory Channel Scan NOTE Only those memory channels that have data entered,and that have not been locked out it will be scanned. Scan does not start more than 2 channels have data entered. Press the F key and then the 6/MEMO key. The MEMO indicator will light to prepare memory scan. 1. Adjust the SQL control to the threshold point. 2. In the memory channel mode press the SCAN key to initiate scan. The MEMO indicator begins flashing as a visual reminder that the transceiver is scanning. Continue to 4-5-3 step 4. 4-5-7. VFO/Memory Channel Scan 1. Adjust the SQL control to the threshold point. 2. Press the F key, then the SCAN/VM. SCAN key initiate VFO/Memory scan. 3. Alternate scanning of the VFO frequency shown on the display and the memory channel last used. Continue to 4-5-3 step 4. 25 4-5-8. CALL Scan CALL/VFO Scan Press the F key, then the CALL/C.SCAN key in the VFO mode to start alternate scanning of the VFO frequency shown on the display and the call channel. CALL/Memory Channel Scan Press the F key, then the CALL/C.SCAN key in the memory channel mode to start alternate scanning of the CALL channel and the Memory channel that was last used. 4-5-9. Memory Channel Lockout This function allows you to specify which memory channels you wish to skip during memory channel scan. 1. Select the memory channel that you wish to skip by pressing the numeric keys. 2. Press the F key. The F indicator lights. Within 10 seconds of pressing the F key, press the O/L.OUT key. A ★ indicator appears under the memory channel number. This indicates that the memory channel will be skipped in the memory channel scan mode. CO L. OUT CO 26 3. Repeat steps 1 and 2 to lock out any other channels you wish to skip. 4. To cancel the lockout, select the desired memory channel as described in steps 1, and 2 above. Press the F key, then the O/L.OUT key. The ★ indicator goes 4-5-10. Priority Alert Function The priority Alert function allows you to monitor memory channel 1 once every 5 seconds for activity even when you are tuned to a different channel number. • Alert by Warning Tone If a signal is present beep will sound from the speaker to indicate that the channel is busy. To activate the priority alert function: 1. Ensure the frequency you wish to monitor has been entered in memory channel 1. 2. Adjust the SQL control to the threshold point. 3. Press the F key momentarily, then press the 1 /AL key. The AL indicator will turn on the display to indicate that this function has been activated. off. F AL 1 4. If a signal is present a beep is heard from th...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :