Be 3® Quasar 12-Volt 2-Mile Navigational Light Without Wire Leads: 3100-3104, 3130-3134 With 7" Wire Leads: 3120-3124, 3150-3154 Attwood marine hardware, navigational lighting, bilge pumps, and other marine accessories are specified more than any other brand by America’s best-known boat manufacturers as original equipment. Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69385 Rev. B 03-10 Meets USCG CFR 183.810, ABYC A-16 requirements, an

Electronic fuel injection, anti-skid braking, and cruise control systems are typical examples of equipment that may malfunction. If your vehicle contains such equipment, consult the dealer for the make of vehicle and enlist his/her aid in determining if they will perform normally while transmitting. PREPARATION PREPARATION Note: The following preparation instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. TOOLS REQUIRED Note: Before installing

Installation Precautions Tighten/remove with wrench on hex fitting only. Do not attempt to rotate gauge by turning housing. Use fittings appropriate for the pressure range of the gauge. Do not apply vacuum to gauges not designed for vacuum operation. NEVER insert objects into the gauge port or blow out with compressed air. Permanent damage not covered by warranty will result to the sensor. The DPG1100AD and DPG1100ADBL can be powered by any AC source of 8 to 24 VAC 50/60 Hz, or any DC source of

The normalized values of these four analog levels are: +3, +1, –1 and –3. Each represents a symbol or quat. To provide precise adjustment of the transmitted power, the level of the DAC may be adjusted. The Transmitter Gain Register [tx_gain; 0x29] sets the level. During the manufacturing of the Bt8960, one source of variation in the transmitter levels is process variations. The Transmitter Calibration Register [tx_calibrate; 0x28] contains a read-only value which nulls this variation. The value

In the United Kingdom a 1750 Hz tone burst at the beginning of each transmission is used. Since use of these tones is required in the U.K. and in Europe the tone encoder is included as standard equipment. Tone frequency selection To select the tone frequency, press the F and the R/TONE.F key. The display will show a operating tone frequency. Press either the A key or the ▼ key momentarily, the frequency will change 1 step up or down. Press the enter key to complete the selection. Tone Squelc

An OMEGA Te c h n o lo g ie s Co m p a n y DP18 Series Model DP18-RT1 True RMS Ammeter .............................................................................................................................................................................................................................................................................................................................................................................................................................

ORDER NO. DESCRIPTION M. H/VLOCATION R682 7030005700 S.RES ERJ2GEJ 274 X (270 k.) B 6.6/26.5 R683 7030006610 S.RES ERJ2GEJ 394 X (390 k.) B 12/29.3 R684 7030003830 S.RES ERJ3GEYJ 185 V (1.8 M.) B 13.2/29.7 R685 7030007340 S.RES ERJ2GEJ 153 X (15 k.) B 8.4/31.4 R686 7030005120 S.RES ERJ2GEJ 102 X (1 k.) B 8.1/33.2 R687 7030005120 S.RES ERJ2GEJ 102 X (1 k.) B 5.4/31.3 R688 7030005080 S.RES ERJ2GEJ 823 X (82 k.) B 4.3/34.2 R689 7030005240 S.RES ERJ2GEJ 473 X (47 k.) B 3.6/33.2 R690 7030010040 S.RES

Failure to do this may result in serious personal injury. Electrical Safety If you are unsure how to attach wires to terminals, DO NOT continue. Contact a qualified electrician for assistance. Connecting wires improperly may cause them to come loose or contact other wires, which can cause electrocution, fire, or a short. Awarning Electrocution or fire could result if this motor is not grounded correctly or if your wire connections do not comply with local and state codes. Ensure compliance b

(Because of DC voltage is present at the plug.) • When the plug is inserted in this jack, the built-in microphone is automatically disconnected. (D SP jack (Speaker jack) • Connect an external speaker or earphone. • Used with the MIC jack, for optional SMC-30 or HMC-1. • When the plug is inserted in this jack, the built-in speaker is automatically disconnected. 0 Antenna connector • Insert the supplied helical antenna and rotate to the right to secure. (D Tone switch • Activates the sub