About Copyright Copyright of this Manual and Software All copyrights and other intellectual property rights for this in-depth manual and relevant technical documents as well as the software described in this in-depth manual and relevant technical documents, and help texts and manuals attached to the software are owned by Kenwood Corporation. A right to use the software described in this in-depth manual and relevant technical documents, and help texts and manuals attached to the software is grant
Electronic fuel injection, anti-skid braking, and cruise control systems are typical examples of equipment that may malfunction. If your vehicle contains such equipment, consult the dealer for the make of vehicle and enlist his/her aid in determining if they will perform normally while transmitting. PREPARATION PREPARATION Note: The following preparation instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. TOOLS REQUIRED Note: Before installing
FleetSync enables a variety of paging functions on your transceiver, some of which depend on dealer programming. Note: This function is available only in Conventional FM Operation. KEY FUNCTIONS Key Function Selcall or Selcall + Status Press to change the transceiver mode as shown in the diagram below. CH control Rotate to select an ID from the pre-programmed ID list or Status list. PTT switch or PF4 key Press to initiate a call. Keypad 0 ~ 9 Use the DTMF keypad to enter Selcall or Status number
2 and manufactured with highest quality of Features................................................................. 4 microelectronics technology and workmanship. We are Optional Accessories............................................ 5 confident that you will be entirely satisfied with the Controls and Connections.................................... 6 superb performance and reliability of this Hand-Held Getting Ready........................................................10 (H/H) Transcei
The normalized values of these four analog levels are: +3, +1, –1 and –3. Each represents a symbol or quat. To provide precise adjustment of the transmitted power, the level of the DAC may be adjusted. The Transmitter Gain Register [tx_gain; 0x29] sets the level. During the manufacturing of the Bt8960, one source of variation in the transmitter levels is process variations. The Transmitter Calibration Register [tx_calibrate; 0x28] contains a read-only value which nulls this variation. The value
1 using supplied hardware. 4. Connect the electrical wiring for power, illumination, and ground as shown in FIG. 1. Connect supplied data line to remote, route to the radio and connect to the connector on the rear of the radio as shown in FIG. 2. 2 AMP FUSE BLUE Data line (connect to radio) BLACK: ground YELLOW Illumination (connect to instrument lighting) RED + 12V switched/ignition A NUT LOCK WASHER WASHER cm MOUNTING SURFACE GASKET REMOTE FIG. 1 Note, The rear view of radio an
We believe this easy-to-use transceiver will provide you with dependable and reliable communications. This KENWOOD transceiver is a precision device. Treat it with care, and you will enjoy years of reliable operation. FEATURES • Compact design with a sturdy, polycarbonate body and a spring- loaded belt hook. • Can be used with the supplied Ni-MH battery pack or 3 AA batteries. • 15 channels with 121 tone/code settings for each channel, allowing you to ignore unwanted calls. • Privacy Talk scramb
TH-41 5E: 430 MHz FM transceiver with Tone. (with Tone Burst for U.K. version) TH-315A: 220 MHz FM transceiver with DTMF. TH-215A: 144 MHz FM transceiver with DTMF. TH-215E: 144 MHz FM transceiver with Tone. (with Tone Burst for U.K. version) SAVE THIS INSTRUCTION MANUAL. Under normal circumstances, the transceiver will operate in accordance with these operating instructions. The transceiver was preset at the factory and should only be readjusted by a qualified technician with proper test eq
Do not allow the battery to charge for greater than 1 5 hours. The useful life and battery performance will be reduced if you exceed the recommended charge period. NOTES:-— • Turn off the power switch before charging. • Recharging should be done within an ambient temperature between 10°C~40°C (50°F~ 104°F). Recharging performed out of this range may not fully charge the battery. MANGANESE or ALKALINE BATTERIES Load 6 x R6 (AA) manganese or alkaline batteries in series in the supplied batter
Do not touch them. • Should the unit require service, contact your authorized dealer. This Instruction Manual covers the following models: Illustrations show the TH-41 BT. TH-41 A 430/440 TH-41 BT 430/440 TH-41 E 430/440 TH-31 A 220 MHz TH-31BT 220 MHz TH-21A 144 MHz TH-21BT 144 MHz TH-21 E 144 MHz 2 Contents 1. Accessories........................................................................................ 3 2. Specifications.....................................................