Évaluations - 5, GPA: 3.4
(
)
)
|
Facilité d'utilisation
only very briefly. 6. After adjusting recording level, press the PAUSE button again to put the unit into recording mode and to start the tape. 7. Carefully watch the meter indication during recording as well. PAUSE button may be used to temporarily halt recording. 8. Press STOP/EJECT button when recording is finished. When the end of the tape is reached, the recording mode will automatically disengage and tape stops. Playback 1. Set the Dolby NR button in depressed position when you play back a tape recorded with Dolby NR. Release the button when you play back a tape not recorded with Dolby NR. When you play back a tape recorded with Dolby NR. also set the Dolby B-C type selector button according to whether Dolby NR. B or C, is used. 2. Set the tape selector to match the type of tape used. 3. Turn on the power switch on your amplifier, keeping its volume control set to minimum. When using headphones connected to the deck, the amplifier is not necessary. 4. Turn on the Power switch on the deck. 5. Press PLAY button and playback will begin. Raise the volume to the desired level. 6. To momentarily halt playback, press the PAUSE button. When you wish to end playback, press the STOP/EJECT button. When the stape comes to an end, It stops automatically and playback mode is disengaged. HEAD CLEANING The most frequent cause of failure to record in one or both channels, or of weak, distorted sound, is dirty tape heads and capstan. So, be sure to clean the heads, capstan, pinch roller and tape guides as often as possible using a "Q” tip dipped in ordinary rubbing alcohol or commercial liquid tape head cleaner. Thoroughly wipe the surface of the heads, capstan, roller and tape guide. HEAD DEMAGNETIZING The tape heads, capstan and tape guides gradually become magnetized with use, which will eventually affect the sound quality of your tapes. Demagnetizing should follow cleaning, but need not take place as often as cleaning, once after every 20 to 30 hours of use should suffice. A demagnetizer may be purchased at a moderate cost from any dealer carrying tape recording accessories. Follow the instruction supplied with the demagnetizer. Caution: Be sure to turn off the unit before you attempt demagnetizing. VOLTAGE SELECTION Not available for U.K., Canada and Scandinavia The unit is a variable voltage equipment that can run on 120V, 220V or 240V power supply. Your unit should already be preset at the proper voltage for use in your area. However, if you move to an area where the power supply voltage is different, consult your dealer. SPECIFICATIONS Heads: Rec/Play......................Sendust Guard Erase.........................Ferrite core Track..........!.....................4-track/2-channel Tape Speed..........................4.8cm/sec. Motor................................Electronic DC Governor Wow and Flutter......................0.2% (DIN) 0.08% (WRMS) Distortion (REC/PB, 400 Hz)...........1.0% (METAL) Frequency Response (- 20 dB)........Normal, LH 30 to 17,000 Hz ± 3 dB SPECIAL 30 to 17,000 Hz±3 dB Metal 30 to 18,000 Hz ±3 dB Siflnal-toNolse Ratio (WTD. 0 dB = 580 mV, Chromium)..........Dolby NR in: 64 dB (B type) 72 dB (C type) Dolby NR out: 55 dB Input Sensitivity/Impedance...........MIC 0.3 mV/10 kohms LINE 58 mV/33 kohms Output Level/Impedance: LINE...............................580 mV/1 kohm Fast Wind Time (C-60).................90 seconds Tape Selector BIAS EQUALIZER Normal, LH........................100% 120/js Special............................150% 70*js Metal.............................. 220% 70>js MISCELLANEOUS Power Requirement...................120V/60 Hz, 220V/50 Hz, 240V/50 Hz. or 120, 220. 240V/50-60 Hz (depending on destinations) Power Consumption..................22 watts Dimensions (Overall)..................430 (W) x 117 (H) x 270 (D) mm 16-15/16" x 4-5/8" x 10-5/8” Weight (net)..........................3.9 kg/8.58 lbs. • Specifications and design subject to possible modification without notice. • Dolby and the double-D symbol are trade marks of Dolby Laboratories Licensing Corporation. Noise reduction system manufactured under license from Dolby Laboratories Licensing Corporation. 3 йбШИНЯмИ el ТАРЕ SELECTOR SETTING GUIDE BANDSORTENEINSTELLUNG GUIDE DE REGLAGE DE SELECTEUR DE BANDE TDK.............. . D, OD, AD.............. . . . . NORMAL FUJI FILM........ . ER. DR, FR I............ . . . . NORMAL SONY............ . AHF. BHF, CHF......... . . . . NORMAL MAXELL.......... . UL, UD, XL-I ,NEW-XLI NORMAL SCOTCH ......... . BX, CX.XS I ........... . . . . NORMAL BASF............. . LH-X. PRO-I............. NORMAL TDK.............. .MA, MA-R.............. .... METAL FUJI FILM........ .FR..................... .... METAL SONY............ .METALLIC.............. .... METAL MAXELL.......... . NEW-MX............... .... METAL SCOTCH ......... . METAFINE............. .... METAL BASF............. . PRO-IV................. METAL TDK....