• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. — 23 — 23— 23 — —— Connecting Connecting KENWOOD disc changer To connect the Disc changer, consult your Disc – + + + + + FRONT • L FRONT • R REAR • L REAR • R P.CONT ANT. CONT. Rear right output (Red) Rear left output (White) FM/AM antenna input changer manual. Wiring harness (Accessory1) TEL mute terminal Fuse (10A) Plug (page 25) White/Black Gray/Black Green/Black Purple/Black White Gray Green Purple To front left speaker To front right speaker To rear right speaker To rear left speaker Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) - (To car chassis) Ignition key switch Car fuse box (Main fuse) ACC Car fuse box Battery Power Control terminal (page 26) Power control/ Motor antenna control wire (Blue/White) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. If no connections are made, do not let the wire come out from the tab. Antenna Cord (ISO) Car’s wiring harness Antenna Conversion Adaptor (ISO–JASO) (Accessory6) — 24 — 24— 24 — —— ¦ ¦ Plug Setting ¦ ¦ Plug Setting 10 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8Connector A Connector B Pin Numbers Plug Functions for ISO Connectors setting* A–4 1 Battery 2 Ignition (ACC) A–5 Power Control A–7 1 Ignition (ACC) 2 Battery A–8 Earth (Ground) Connection B–1 Rear Right (+) B–2 Rear Right (–) B–3 Front Right (+) B–4 Front Right (–) B–5 Front Left (+) B–6 Front Left (–) B–7 Rear Left (+) B–8 Rear Left (–) *Plug setting: See right side. — 25 — 25— 25 — —— 2WARNING Connecting the ISO The pin arrangement for of vehicle you drive. Make to prevent damage to the unit. 1 The A-7 pin of the vehicle's ISO ignition, and the A-4 pin is connected supply. (Default setting) 10 2 The A-7 pin of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin is linked to the ignition. 10 • If both the A-7 pin and A-4 pin are connected to the vehicle constant power supply, use Plug setting 2. • If the A-7 pin is connected to the vehicle constant power supply, and the A-4 pin isn't connected to anything, wire the unit using the Wiring harness (Accessory 1). English English ¦ Power Control Connections The output of the Power with the power on/off This terminal can be connected CON (REMOTE) terminal of the amplifier. (MAX. 300 mA) Power Control terminal (Flat terminal) Power control wire Power Amplifier — 26 — 26— 26 — —— Installation Installation Installation Firewall or metal support Self-tapping attach it in place. screw (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip) . Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and Metal mounting strap (commercially available) ¦ Installing in Japanese-1 Refer to the section 28) and then remove the 2 Align the holes in the unit (vehicle mounting bracket and accessory screws. T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. ¦ Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (o4 . 16 mm) in the hole shown below. Accessory 5 8 mm MAX. o5mm o5mm 8mm MAX. T N N T T/N 3 4 Never insert the taptite screw (o4 . 16 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit. — 27 — 27— 27 — —— Installation Installation ¦ Removing the ¦ Removing the 1 Refer to the section 1 Engage the catch pins then remove the hard locks on the lower level. Lower the frame and pull 2 Remove the screw (M4.8) on the back panel. 3 Insert the two removal tools deeply as shown. Removal tool 2 When the lower level is removed, remove the upper locations. The frame can be removed from the top side in the same manner. Catch Lock Accessory 2 Accessory 2 Removal tool Screw (M4X8) (commercially available) 4 Lower the removal tool toward the bottom, and pull out the unit halfway whilst pressing towards the inside. 5 Pull the unit all the way out with your hands, being careful not to drop it. Be careful to avoid injury from the catch pins on the removal tool. — 28 — 28— 28 — —— Troubleshooting Troubleshooting General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? Nothing happens when the b...
)
