Évaluations - 3, GPA: 3.3 ( )

Fabricant : Makita Taille : 936.14 kb Nom Fichier : Langue d'enseignement:

Match the hole in the pipe case to the hole in the holder case and fasten the pipe case to the engine with damper bolt, wave washer and washer. (Tightening torque: 70 ~ 100 kg.cm; 5 7 ft.lbs) ~ CAUTION: Securely tighten the damper bolt, which is one of the important parts mating the engine and machine body. For RBC260 and RBC310 Install the pipe case (the end with circular metal housing) over the clutch assembly and fix with four socket head bolts and fix tightly with hex wrench. 2.Mounting of handle For RBC230 I RBC261 I RBC311 As shown at right, tighten the loop handle with three socket head bolts. Mount the handle so that the throttle wire guide will he oriented to the right, as viewed from the engine side. The standard position of the handle is 200 to 250 mm (7-718” 9-718”) from the hanger. Position ~ the handle according to a worker’s stature and working conditions. 171 a0 141 151 161 11 1 Holder case 121 Hole 131Pipe case (41Washer 151Wave washer 161 Damper bolt 171 Hole Ill Pipe case 121 Hex wrench 131Socket head bolt For RBC260 and RBC310 The handle comes in three parts; two handles and one handle holder assembly. (One half of handle holder is already fitted to pipe case, the other half of handle holder is in plastic bag with four socket head bolts). Place the two handles in the half of handle holder fitted to pipe case (the flared ends fit into grooves in handle holder). Place the loose handle holder over handles and other handle holder on the pipe case and fix together with the four socket head bolts, Ensure the throttle assembly is on correct side and before final tightening, adjust rake of handle to suit. Route the throttle wire and ignition wires through locations on handle towards engine. 3. Assembly of throttle wire and ignition wire Remove plastic cover from carburetor. Insert throttle wire through adjusting screw and fit nipple of throttle wire into swivel of carburetor. Adjust the adjusting screw to take up free play of wire ensuring the throttle is fully opened when throttle lever is in high speed position and 2 3 ~ mm (0.079" 0.118") free play when in low ~ speed position. Re-fit plastic cover. Connect the female and male bullet connectors from throttle assembly to the male and female bullet connectors coming from engine. , ~- 4. Mounting of protector and nylon cutting head I- Fasten the protector to the pipe case with two socket head bolts and clamp. At this time, the clamp should be installed on the pipe case with its projection inserted into the opening between the gearcase and the pipe case. (1) Gearcase 12)Clamp 131 Socket head bolt (41Pipe case 15) Protector 161 Shaft To install the nylon cutting head, mount the sup- port washer onto the shaft. Insert the hex wrench through the hole in the gearcase and turn the support washer until it will be locked with its notch (or the shaft will be locked). Then screw the nylon cutting head onto the shaft by turning it counter- clockwise. Remove the hex wrench. Ill Hex wrench 121 Gearcase 131 Hole (41Support washer 151 Notch 161 Nylon cutting head ENGINE STARTING AND STOPPING PROCEDURES Starting When the engine is cold (ie. left stopped for more than 5 minutes) or when fuel is added to the engine: 1) First place the machine on the ground. 2) Give a gentle push on the primer pump repeatedly (7 -10 times) until fuel comes into the primer pump. 3)Close the choke lever. I (1)Primer pump (2)Choke lever 4) Push the stop switch to "START" position (or RBC230 / RBC261i RBC311 I RBC260 / RBC310 opposite of "STOP" position). (1I Stop switch 5) For RBC230 / RBC261 / RBC311 I RBC230 / RBC261/ RBC311 I RBC260 / RBC310 Squeeze the throttle lever fully. Then release the' throttle lever while depressing the throttle lock button. The throttle lever will now be locked in the "start-up" position. For RBC260 and RBC310 Press the "LOCK-OFF" switch before squeezing the throttle lever. Then squeeze the throttle lever fully. Release the throttle lever while depressing the throttle lock button. The throttle lever will now be locked in the "start-up" position. 1 (1) Throttle lever (2) Throttle lock bu...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :