Log:
Évaluations - 3, GPA: 4 ( )

Instructions Makita, Modèle BRUSH CUTTER RBC281

Fabricant : Makita
Taille : 2.14 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Do not perform any modifications on the brush cutter or string trimmer as this will endanger your safety. The performance of maintenance or repair work by the user is limited to those activities as described in the instruction manual. All other work is to be done by Authorized Service Agent. Use only genuine spare parts and accessories released and supplied by MAKITA. Use of non-approved accessories and tools means increased risk of accidents. MAKITA will not accept any liability for accidents or damage caused by the use of non-approved cutting tools and fixing devices of cutting tools, or accessories. First aid In case of accident make sure that a first-aid box is available in the vicinity of the cutting operations. Immediately replace any item taken from the first aid box. When asking for help, please give the following information: - Place of accident - What happened - Number of injured persons - Kind of injuries - Your name □ Packaging The MAKITA brush cutter or string trimmer will be delivered in two protective cardboard boxes to prevent transport damage. Cardboard is a basic raw material and is therefore consequently reusable or suitable for recycling (waste paper recycling). 6 SPECIFICATION Model RBC280 RBC320 Dimensions (mm) (LxWxH) (mm) 1,795 x 590 x 340 (70-5/8" x 23-7/32" x 13-3/8") Weight (kg) 5 9 5.9 Revolution of cutter head (rpm) 6,000 Gear ratio 13/19 13/19 Clutch Automatic centrifugal type Engine EC027G EC031G Displacement (cc) 27 2 30.5 Power rating (PS) 1.1 1.3 Carburetor All position diaphragm type Starting system Recoil starter Ignition system Solid state ignition Spark Plug NGK-BM7A or equivalent Fuel Tank (t) 0 8 (0.77 quarts) Fuel Mixed gas (Gasoline : Makita Two-stroke Engine oil = 50 : 1) Model RBC281 RBC321 Dimensions (mm) (mm) 1,795x240x245 (LxWxH) (70-5/8" x 9-7/16" x 9-5/8") Weight (kg) 5.9 5.9 Revolution of cutter head (rpm) 6,000 Gear ratio 13/19 13/19 Clutch Automatic centrifugal type Engine EC027G EC031G Displacement (cc) 27.2 30.5 Power rating (PS) 1.1 1.3 Carburetor All position diaphragm type Starting system Recoil starter Ignition system Solid state ignition Spark Plug NGK-BM7A or equivalent Fuel Tank (t) 0.8 (0.77 quarts) Fuel Mixed gas (Gasoline : Makita Two-stroke Engine oil = 50 : 1) NOTE : Specification are subject to change without notice. 7 DESIGNATION OF PARTS RBC280 DESIGNATION OF PARTS DESIGNATION OF PARTS DESIGNATION OF PARTS DESIGNATION OF PARTS 1 Metal Blade 7 STOP Switch 20 Fuel Filler Cap 2 Nylon Cutting Head 8 Throttle Wire 15 Air Cleaner 21 Recoil Starter 3 Gear Case 9 Handle Joint 16 Muffler 22 Fuel Tank 4 Drive Shaft 11 Hanger 17 Muffler Exhaust Port 23 Guard (for Nylon Cutting Head) 5 Handle 12 Waist Pad 18 Choke Lever 24 Guard (for Metal Blade) 6 Throttle Lever 13 Holder Case 19 Starter Knob 25 Shoulder Strap 8 ASSEMBLY OF ENGINE CAUTION : Before performing any work on the brush cutter or the string trimmer, always switch off the motor and pull the spark plug connector off the spark plug. Beware of hot engine parts and sharp blade edges. Always wear protective gloves! CAUTION : Start the brush cutter or the string trimmer only after having assembled it completely. 1 Loosen the screws (1) and insert the drive shaft into the holder case. (Note) Always insert the drive shaft (2) into the holder case (3) fully. If the inner shaft (4) resists resists full insertion of the drive shaft, try to insert it again after slightly rotating"the drive shaft or the support washer on the gear case to match the inner shaft to the hole inside the holder case. 2. After making sure that the drive shaft is installed fully and properly, tighten the screws (1) to secure the drive shaft. 9 MOUNTING OF HANDLE For RBC280 and RBC320 - Adjust the handle (1) to the proper position end secure the handle joint (2) by tightening the four socket head bolts M5 (3) evenly. - Pass the throttle wire through the handle joint. For RBC281 and RBC321 - Secure the loop handle (9) by tightening the four socket head bolts (8) - The standard position of the handle is 200 to 250 mm from the hanger (10). Position the handle according to a worker’s stature and working conditions. A © © Assembly of throttle wire and ignition wire - Remove the air cleaner cover from the carburetor. - Insert throttle wire (1) through adjusting screw (2) and fit the nipple of the throttle wire into swivel (3) of the carburetor. - Adjust the adjusting screw to take up free play of the throttle wire ensuing the throttle is fully opened when the throttle lever is in high speed position and 2-3 mm (0.079" - 0.118") free play when in low speed position. A © © - Connect the female and male bullet connectors (4) from the throttle assembly to the male and female bullet connectors coming from engine. - Retouch the air cleaner cover. For machines with U handle - Place the waist pad (5) over the throttle wire (guid...

Ce manuel est également adapté pour les modèles :
Clippers - BRUSH CUTTER RBC280 (2.14 mb)
Clippers - BRUSH CUTTER RBC320 (2.14 mb)
Clippers - BRUSH CUTTER RBC321 (2.14 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories