Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years. To reduce the risk of RSI/CTS, do the following: • Avoid using your wrist in a bent, extended, or twisted position. Instead, try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger. • Take periodic breaks to minimize repetition and rest your hands. • Reduce the speed and force with which you do the repetitive movement. • Do exercises to strengthen the hand and arm muscles. • Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage can be prevented. WARNING DANGER Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the Manuals • Provide all users of this equipment with the Operator's Manual and Safety Manual for instructions on Safe Operation. Clear the Work Area • Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15 m (50 ft.) while the unit is in use. Keep a Firm Grip • Hold the front and rear handles with both hands, with thumbs and fingers tightly encircling the handles. Keep a Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach. Avoid Hot Surfaces • During operation, the drive shaft housing, attachment bearing housing and muffler cover area may become very hot, too hot to touch. Avoid contact during and immediately after operation. 6 EQUIPMENT Before operation a complete check of the unit must be performed; • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Inspect shield for damage and ensure that cut-off knife is securely in place. Replace if shield is damaged or missing. • Check that the cutting attachment is firmly attached and in safe operating condition. • Check that front loop handle and shoulder strap/ or shoulder/waist harness are adjusted for safe, comfortable operation. See Assembly Section for proper adjustment. DESCRIPTION Locate this safety decal on your attachment. Make sure the decal is legible and that you understand and follow the instructions on it. If it cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING P/N 89016054130 1. LOWER DRIVE SHAFT ASSEMBLY - Includes the Debris Shield Assembly, Gear Housing assembly, Flexible Drive Cable, Rapid LoaderTM Head and Safety Decals. 2. FLEXIBLE DRIVE CABLE -Cable end fits into upper drive shaft coupler. Lubricate drive cable every 25 hours with ECHO® LUBETM grease. 3. PLASTIC DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack). MUST be installed on unit before use, see Assembly Instructions. Shield assembly includes the Cut-Off Knife. Mounts on the Gear Housing Assembly just above the cutting attachment. Helps protect the operator by deflecting debris produced during the trimming operation. This shield must be replaced with the steel shield for blade use. 4. CUT-OFF KNIFE -Trims line to the correct length. 5. RAPID LOADERTM HEAD - Contains replaceable nylon trimming lines. 5 1 2 3 4 instructions for specific information. PAS RAPID LOADERTM TRIMMER ATTACHMENT OPERATOR'S MANUAL 7 CONTENTS After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. __ 1 -Pro Attachment SeriesTM Trimmer Attachment __ 1 -Operator's Manual __ 1 -Safety Manual __ 1 -Warranty Registration Card __ 2 -Locking Tools __ 1 -Wrench 17 x 14.5 __ 1 -Rapid LoaderTM Head __1 -Nut __ 1 -Washer 10x32x1.2 __ 1 -Plastic Debris Shield __ 1 -Split Pin __ 1 -Shield plate __ 3 -5mm x 16mm Screws (shield mounting) __ 1 -Storage Hook Assembly ASSEMBLY WARNING DANGER Do not perform maintenance or assembly procedures with engine running. Tools Required: Screwdriver, Head Locking Tool, 17x14.5mm Wrench, Needle Nose Pliers Parts Required: Power Head Shaft, Attachment Lower Shaft Assembly, Plastic Shield, Shield Plate, three (3) 5mm x 16mm screws, Rapid LoaderTM Head POWER HEAD SHAFT/ATTACHMENT LOWER SHAFT ASSEMBLY 1. Set Power Head/Shaft Assembly on a level surface. 2. Pull locator pin (A) and rotate counter clockwise 1/4 turn to lock out position. 3. Remove vinyl cap from attachment drive shaft. 4. Remove cardboard spacer, if necessary. 5. Carefully fit attachment lower drive shaft assembly into coupler (B) to decal assembly line (C), making sure that the inner lower drive shaft engages into the upper drive shaft mount. A B D 8 NOTE Earlier model Power Heads may have shorter couplings. Short couplings fit flush to decal point (E). New couplings are 4-3/4 in. long, and fit ...
Ce manuel est également adapté pour les modèles :Clippers - 99944200610 (214.45 kb)