Évaluations - 0, GPA: 0 ( )

Fabricant : Philips Taille : 919.8 kb Nom Fichier : Langue d'enseignement:

10 minutes of operating time left) and you need to recharge the appliance. Note:The appliance can only be charged in the charger. 1 Switch off the appliance before you charge it. 2 Insert the small plug into the charger (Fig. 3). Note:The small plug is easiest to insert when the charger is folded. 3 4 5 Unfold the charger (‘click’) (Fig. 4). Put the adapter in the wall socket. , , Put the appliance in the charger (Fig. 5). The charging light starts to flash green to indicate that the appliance is charging (Fig. 6). When the battery is fully charged, the charging light lights up green continuously. After approx. 30 minutes the charging light , goes out to save energy. Optimising the lifetime of the rechargeable battery Discharge the rechargeable batter y completely twice a year by letting the motor run until it stops. Then fully recharge the batter y. Using the appliance You can use the appliance wet or dr y to shave or trim hair on all par ts of the body below the neckline. Do not use this appliance to shave or trim facial or scalp hair. Tip:Take your time when you first start to shave sensitive areas.You have to acquire practice with the appliance.Your skin also needs some time to adjust to the procedure. Trimming The trimming comb allows you to cut hair to 5 different lengths. Star t with the highest setting (5) to acquire practice with this appliance. Hair length setting Hair length after trimming 1 3mm 2 5mm 3 7mm 4 9mm 5 11mm 1 Hold the appliance in the trimming position, with the trimming unit pointing upwards and the shaving unit pointing downwards (Fig. 7). 2 Press the hair length setting selector (1) and then move it up or down (2) to select a setting (Fig. 8). -The two lines next to the setting selector show which setting you have selected (Fig. 9). 3 4 Press the trimming unit on/off button once to switch on the trimming unit (Fig. 10). To trim the hair, move the trimming comb through the hair slowly (Fig. 11). Tips -Always make sure that the tips of the trimming comb point in the direction in which you move the appliance. -Make sure that the flat par t of the trimming comb is always fully in contact with the skin to obtain an even result. -Since all hair does not grow in the same direction, you need to move the appliance in different directions (upward, downward or across). -Trimming is easier when the skin and hair are dr y. 5 When you are finished, press the trimming unit on/off button again to switch off the trimming unit (Fig. 10). shaving Before you use the shaving unit, always check it for damage or wear. If the shaving unit is damaged or worn, do not use it, as injury may occur. Replace a damaged shaving unit before you use it again (see chapter ‘Replacement’). Hold the appliance in the shaving position, with the shaving unit pointing upwards and the trimming unit pointing downwards (Fig. 12). 1 2 3 4 Press the shaving unit on/off button once to switch on the shaving unit (Fig. 13). Place the shaving unit on the skin (Fig. 14). Move the appliance against the direction of hair growth while you press it lightly (Fig. 15). Tips -Stretch your skin with your free hand to make the hairs stand upright. -Make sure that the shaving unit is always fully in contact with the skin. -If the hairs are longer than 10mm, trim them first to make shaving easier. 5 To switch off the shaving unit after use, press the shaving unit on/off button again (Fig. 13). Cleaning and maintenance Clean the appliance after ever y use. Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrolor acetone to clean the appliance. Note:The trimming unit and shaving unit do not need any lubrication. 1 2 3 Switch off the appliance. Rinse the appliance under the tap. Cleaning the shaving unit Pull the shaving unit off the appliance. (Fig. 16) Note: The shaving unit is ver y delicate. Handle it carefully. Replace the shaving unit if it is damaged. 4 Rinse the shaving unit with lukewarm water. (Fig. 17) Do not clean the shaving unit with the brush, as this may cause damage. Remove hairs from the hair chamber with the cleaning brush and/or with lukewarm water (Fig. 18). After cleaning, snap the shaving unit back onto the appliance (‘click’) (Fig. 19). Cleaning the trimming unit Remove the trimming comb by sliding it off the appliance. Push the middle part of the trimming unit upwards with your thumb until it opens (Fig. 20). Remove hairs from the hair chamber with the cleaning brush and/or with lukewarm water. (Fig. 21) 5 6 7 8 9 10 Rinse the trimming unit with lukewarm water (Fig. 22). 11 After cleaning, close the trimming unit and reattach the trimming comb. (Fig. 23) Replacement In case of frequent use, replace the shaving unit (type number TT2000) ever y year. Replace a damaged shaving unit immediately. To replace the shaving unit: 1 2 Pull the shaving unit off the appliance. (Fig. 16) Snap the new shaving unit onto the appliance (‘click’) (Fig. 19). storage You can fold the charger for...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :