Évaluations - 0, GPA: 0 ( )

Fabricant : Philips Taille : 8.76 mb Nom Fichier : Langue d'enseignement:

general -The appliance complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap. compliance with standards This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. charging QS6160 only: Charging normally takes approx. 1 hour. QS6140 only: Charging normally takes approx. 4 hours. When the appliance is fully charged, it has an operating time of 50 minutes. Batter y status indicator : -When the batter y status indicator flashes white, the batter y is being charged. -When the batter y status indicator lights up white continuously, the batter y is fully charged.This indication is shown for 30 minutes and then the batter y status indicator goes out. -When the batter y status indicator flashes orange, the batter y is almost empty (approx. 10 minutes of operating time left). -When the batter y status indicator flashes orange quickly, the batter y is empty and you have to charge the appliance before you can use it again. Note:The appliance can only be charged in the charging stand. 1 Insert the small plug into the charging stand. Note:The small plug is easiest to insert when the charging stand is folded. 2 3 Unfold the charging stand (‘click’). Put the adapter in the wall socket. EngliSh 4 Put the appliance in the charging stand. The battery status indicator starts to flash white to indicate that the , appliance is charging. When the battery is fully charged, the battery status indicator lights , up white continuously. using the appliance You can use the appliance to trim or dr y shave facial hair (beard, moustache and sideburns).This appliance is not intended for shaving or trimming lower body par ts. Tip:Take your time when you first start to shave.You have to acquire practice with the appliance.Your skin also needs some time to adjust to the procedure. trimming with comb The trimming combs allow you to trim to different lengths. Star t at the highest setting to acquire practice with this appliance. See the table below for an over view of the hair length settings and the corresponding hair lengths. Setting Hair length after trimming 1 1 mm - 3/64 inch . 1.5 mm - 1/16 inch 2 2 mm - 5/65 inch . 2.5 mm - 3/32 inch 3 3 mm - 1/8 inch 4 4 mm - 5/32 inch 5 5 mm - 3/16 inch 6 6 mm - 1/4 inch 7 7 mm - 9/32 inch 8 8 mm - 5/15 inch EngliSh Setting Hair length after trimming 9 9 mm - 3/8 inch 10 10 mm - 13/32 inch * no comb = 0.5mm - 1/32 inch 324 1 Hold the appliance in the trimming position, with the trimming head pointing upwards and the shaving head pointing downwards. 2 Slide the comb into guiding groove of the appliance (‘click’). 3 Press the hair length setting selector and then move it from left to right or right to left to select a setting. -The line above the hair length setting selector shows which setting you have selected. 10 EngliSh 4 Press the trimming head on/off button once to switch on the trimming head. QS6160 only:The on/off button lights up to indicate that the , trimming head is operating. 5 To trim the hair, move the trimming comb through the hair slowly. tips -Always make sure that the tip of the trimming comb points in the direction in which you move the appliance. -Make sure that the flat par t of the trimming comb is always in full contact with the skin to obtain an even hair length result. -Since hair grows in different directions, you need to move the appliance in different directions as well (upward, downward or across). -You can switch on the trimming head while the shaving head is operating. If you do this, the shaving head is switched off immediately. -Trimming is easier when the skin and hair are dr y. 6 When you are finished, press the trimming head on/off button again to switch off the trimming head. trimming without comb The comb keeps the trimming head at a set distance from your head.You can use the trimming head without comb.If you use the trimming head without comb, your hair is cut off close to the skin (approx. 0.5 mm). 1 To remove the comb, pull it off the appliance. Never pull at the flexible top of the comb. Always pull at the bottom par t. 2 3 Press the trimming head on/off button to switch on the trimming head. Hold the appliance with the trimming head pointing upwards and make downward strokes with the broad side of the trimming head. Using the precision trimmer The precision trimmer is only half as wide as the broad side of the trimming head. It therefore allows more precise styling of the area around the ears, the sideburns and also around the mouth and under the nose. 1 To use the precision trimmer, simply turn the cutting unit until the precision trimmer points towards the front of the appliance. 2 Press the trimming head on/off button to switch on the trimming head. 3 Hold the appliance with the trimming head pointing upwards and make downward strokes with ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :