Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
• Position the handle in place as shown in figure 1 (TR1800, HT2200, HT22D) or figure 1A (HS1010). • Reinsert the phillips head screws into the openings on the side of the handle and tighten securely. ATTACHING EXTENSION CORD TO TRIMMER An extension cord retainer is built into the switch handle that prevents the tool from coming unplugged. To use this feature, simply double the extension cord about 8 inches from the end, and insert it into the slot in the bottom of the handle area. Hook the loop formed by doubling the cord over the tab, as shown in figure 2 (TR1800, HT2200, HT22D) or figure 2A (HS1010). Gently tug on the cord to insure that it is firmly retained in the trimmer’s handle. Plug the receptacle end of the extension cord into the plug blades in the trimmer. SAVE THESE INSTRUCTIONS FOR FUTURE USE Minimum Gage for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere Rating More Not more American Wire Gage Than Than 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended 7 KEY INFORMATION YOU SHOULD KNOW: • To insure extension cord does not come loose see Figures 2 and 2A for proper attachment. • In order to operate the trimmer, the lock button must first be pulled back (see figure 3) then squeeze trigger. 3 Lock Button Bouton de verrouillage Boton de seguridad Trigger Gachette Interruptor de Gatillo Plug Blades Raccordement a fiche Clavijas de enchufe DATE CODE BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL 1-800-544-6986 BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER. THANK YOU FOR CHOOSIING BLACK & DECKER!! GO TO WWW..BLACKANDDECKER..COM//NEWOWNER TO REGIISTER YOUR NEW PRODUCT.. 1 2 6 1A 2A OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS TO TURN THE TOOL ON Pull the LOCK BUTTON back with your thumb and then squeeze the TRIGGER with your fingers as shown in Figure 3. (Once the tool is running you can release the LOCK BUTTON.) To turn the tool OFF, release the TRIGGER. TO LOCK THE TOOL ON FOR CONTINUOUS RUN WITH THE TOOL RUNNING, pull the LOCK BUTTON ALL THE WAY back, release the TRIGGER, then release the LOCK BUTTON. The tool is now locked ON. To turn the tool OFF, squeeze and release the TRIGGER. NOTE: In order to lock the tool on, it is important to first release the trigger and then release the lock button. TRIMMING INSTRUCTIONS 1 EXTENSION CORD – (Figure 4) Always keep extension cord behind trimmer and away from the trimming operation. Never drape it over a hedge being trimmed. If you cut or damage the cord, unplug it at the electrical outlet immediately, before inspecting or repairing cord. 2 WORKING POSITION – Maintain proper footing and balance and do not overreach. Wear safety goggles, non-skid footwear and rubber gloves when trimming. Hold the tool firmly in both hands and turn the tool ON. Always hold the trimmer, as shown in figure 4, with one hand on the switch handle and one hand on the bail handle. Never hold the tool by the blade guard. 3 TRIMMING NEW GROWTH -(Figure 5) – A wide, sweeping motion, feeding the blade teeth through the twigs is most effective. A slight downward tilt of the blade, in the direction of motion gives the best cutting. CAUTION: Do not use the trimmer for cutting stems greater than 3/4” (10mm). Use the trimmer only for cutting normal shrubbery found around houses and buildings. 4. LEVEL HEDGES (Figure 6) – To obtain exceptionally level hedges, a piece of string can be stretched along the length of the hedge as a guide. 5. SIDE-TRIMMING HEDGES (Figure 7) – Begin at the bottom and sweep up. WARNING: TO GUARD AGAINST INJURY, OBSERVE THE FOLLOWING: • READ INSTRUCTION MANUAL BEFORE USING, SAVE INSTRUCTION MANUAL. • KEEP HANDS AWAY FROM BLADES. • KEEP HANDS ON HANDLES. DON’T OVERREACH. • CAUTION: – BLADE COASTS AFTER TURN OFF. • DO NOT USE UNDER WET CONDITIONS. • DO NOT USE WITH DAMAGED EXTENSION CORD. • DO NOT UNPLUG OR STORE WITH SWITCH LOCKED ON. Troubleshooting Problem Possible Cause Possible Solution •Unit will not start. • Cord not plugged in. • Plug in cord. • Circuit fuse is blown. • Replace circuit fuse. • Circuit breaker • Reset circuit breaker. is tripped. • Cord or switch is • Have cord or switch damaged. replaced at Black & Decker Service Center or Authorized Servicer. For assistance with your product, visit our website for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986. MAINTENANCE The cutting blades are made from high quality, hardened steel and with normal usage, they will not require resharpening. However, if you accidentally hit a wire fence, stones, glass or other hard objects, you may put a nick in the blade. There is no need to remove this nick as long as it does not interfere ...