Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
• DO NOT CHARGE APPLIANCE IN RAIN OR IN WET LOCATIONS. SAVE THESE INSTRUCTIONS ADDITIONAL IMPORTANT Trigger lock off Verrouillage de la detente Seguro del gatillo Charging LED Temoin de chargement a D.E.L. LED de carga Guard Protecteur Guarda Hub & Spool Moyeu et bobine Cubo y carrete Upper half Partie superieure Mitad superior Lower half Partie inferieure Mitad inferior Nut & bolt Ecrou et boulon Tuerca y tornillo Air slots Fentes d'aeration Ranuras de ventilacion 1/8” of line Fil de 3 mm(1/8 po) 3 mm (1/8”) de linea Trigger Detente Gatillo Nut & Bolt Ecrou et boulon Tuerca y tornillo Charging port and pin Orifice de chargement et tige Puerto y punta de carga Date Code: ADDITIONAL IMPORTANT SAFETY INSTRUCTIONS • WARNING: When using electric tools, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the following: • Do not incinerate the battery even if it is severely damaged or is completely worn out. The battery can explode in a fire. Check with local codes for possible special disposal instructions. • If any leakage of liquid from the battery cells occurs, discontinue use immediately and return the battery to your local Black & Decker Service Center or authorized service facility. • Never attempt to open the battery for any reason. If the plastic housing of the battery breaks or cracks, immediately discontinue use and do not recharge. • Do not charge appliance in rain or in wet locations. • Use only the following type and size battery: Black & Decker 244373 - 12V. • Use only Black and Decker 12V charger 244374. • Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets and keys. The battery or conductor may overheat and cause burns. • Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. • If the battery case cracks due to a fall or other impact and the electrolyte gel leaks out, wipe it up with a cloth, neutralize the acid with any alkaline substance such as ammonia solution of baking soda. If the electrolyte gets on your skin, immediately flush with water and consult a doctor. • Do not use battery for anything other than with this product or other designated Black & Decker product. ASSEMBLY INSTRUCTIONS • WARNING: The guard must always be on the tool to protect the user. UNIT ASSEMBLY Layout the unit as shown in figure 2. Remove the nut and bolt from the upper section (left portion of Figure 2). Slide the bottom portion into the upper portion as indicated. The two halves should snap together. Re-insert the nut and bolt to the upper section, and tighten bolt. The unit should now be rigidly secured. GUARD ASSEMBLY Remove the screw from the guard and insert the guard into the slot (marked by arrows) in the trimmer head as shown in Figure 3. Ensure the guard is fully inserted. Re-insert the screw through the trimmer head and into the guard and tighten as shown in figure 4. NEVER OPERATE THE TOOL WITHOUT THE GUARD PROPERLY IN PLACE. Use of the unit with out having installed the guard will cause the motor to overheat, and void the warranty. BATTERY THE LEAD ACID BATTERY FOR YOUR TRIMMER IS ONLY PARTIALLY CHARGED AT THE FACTORY. BEFORE USING YOUR TRIMMER, THE BATTERY MUST BE CHARGED FOR A MINIMUM OF 24 HOURS. • If the battery case cracks due to a fall or other impact and the electrolyte gel leaks out, wipe it up with a cloth, neutralize the acid with any alkaline substance such as ammonia solution or baking soda. If the electrolyte gets on your skin, immediately flush with water and consult a doctor. • Your trimmer is equipped with a charger bracket that may be mounted firmly to a wall in your garage, shed or similar building. (Hardware for hanging the bracket is included in the plastic bag packed with the trimmer.) Charging your battery in this bracket is very convenient because it hangs the tool up, out of the way and ensures a good, solid contact between the charging terminals. MOUNTING THE CHARGER BRACKET 1. If you intend to mount, the charger bracket on a wall, follow the instructions listed below. 2. Remove the two screws and plastic anchors from the plastic bag. 3. Use the charger bracket to mark the locations of the holes required. Be sure to mount the bracket high enough so that the trimmer can hang freely from it; about 4 feet (1.2m) from the floor. 4. Drill a .250” (6 mm) diameter hole at each marked location. 5. Insert the plastic anchors into the holes and insert one of the screws in each one. Tighten the screws until the heads are above the anchors just enough so that the charger bracket will fit between the anchor and the screw head. 6. Place the charger bracket on the wall (narrow end up) and make sure that the power cord is positioned in the side slot. Press the charger bracket over the screw heads and slide it down until it sits firmly on the screws. 7. Firmly tighten both...
Ce manuel est également adapté pour les modèles :Clippers - CST800 (2.57 mb)